Manual Novoferm Novomatic 553 (page 11 of 31) (English, Dutch, French, Spanish)

474198

Zoom out

Zoom in

1/31

Deleting all the hand transmitters programmed

for the operator:

Plug in the operator's mains plug and whilst

button pressed.

Menu stage 3: Setting/adjusting the top

end of-travel position

Keep button pressed for 3 seconds.

Number 3 appears in the display.

Wait a short while until the 3 starts flashing.

Press button . The operator causes the door

to travel in the OPEN direction as long as the

button is pressed. The position can be altered

to the CLOSE direction via button .

Once the desired OPEN end-of-travel position

has been reached, press button . The

operator stores the OPEN end-of-travel

position and "4" appears in the display.

Menu stage 4: Setting/adjusting the

bottom end-of-travel position

Wait a short while until "4" starts flashing.

Press button . The operator causes the door

to travel in the CLOSE direction as long as the

button is pressed. The position can be altered

to the OPEN direction via button .

Once the desired CLOSE end-of-travel

position has been reached, press button .

The operator stores the CLOSE end-of-travel

position and "5" appears in the display.

Press button twice until "0" appears.

18a Force-learning cycle

Attention: During this opening and closing

cycle the operator learns the force required to

open and close the door. A force limit does not

apply! The cycles must not be interrupted.

During these cycles "0" appears in the display.

- Press button . The operator causes the

door to open until the top end-of-travel

position has been reached.

- Now press button again. The operator

causes the door to close until the bottom end-

of-travel position has been reached.

- After approx. 2 seconds "0" goes out.

Menu stage 5: The opening force limit

If you have previously quit the setting menu,

press button for 3 seconds until "3"

appears. Then press button twice until "5"

appears.

After approx. 2 seconds the display flashes

showing the set value of the opening force

limit.

The force limit setting can be increased or

decreased via buttons and .

After setting the value, press button .

The display shows "6".

Menu stage 6: The closing force limit

After approx. 2 seconds the display starts

flashing and the set value for the closing force

limit is displayed.

The force limit setting can be increased or

decreased via buttons and .

After setting the value, press button . "0"

appears in the display.

Finally, check the force settings and, if

necessary, repeat the setting procedure.

The maximum force at the main closing edge

must not exceed 150N!

Caution! If the force setting is too high,

persons may be placed at risk of injury.

The factory setting is 4!

Programming the Operator

Control elements

The controls for programming the door

operator are protected by a transparent cover.

The transparent cover can be opened with a

screwdriver.

After the operator has been programmed, the

transparent cover must be closed again.

A - Numerical display shows the menu stage

as well as the selected value.

a - Point display, lights up to indicate "ready

for operation" and flashes on the hand

transmitter code learning completion.

B - Button during the setting/adjustment

phase serves as an "up" button and

outside the menu as a start button.

C - Button during the setting/adjustment

phase serves as a "down" button.

D - Button is used to call up the

setting/adjustment menu, to change the

menu stages and to store the settings.

Programming the control unit is menu-driven.

Pressing button calls up the menu guide.

The numbers displayed indicate the menu

stage. After approx. 2 seconds the display

flashes and the setting can be altered via

buttons and .

The selected setting is stored with button

And the programme jumps automatically to the

next menu stage. By repeatedly pressing

button menu stages can be skipped. To

quit the menu, press button until "0" is

shown again. Outside the menu, button can

be used to generate a start impulse.

Before programming

- Allow door to engage into the carriage.

- Pull out the mains plug. Point display (a)

lights up.

- Make sure that the aerial is correctly

positioned (see figure 13).

- Observe the hand transmitter instructions.

Menu stage 1: Programming the start

function for the hand transmitter

Briefly press button .

"1" is displayed.

As soon as the display flashes, press and keep

pressed for approx. 1 second the button of the

hand transmitter, with which you later wish to

start the operator.

As soon as the code has been read, the red

point display (a) flashes five times before

quitting.

Further hand transmitters (up to a maximum of

10) can be programmed.

Menu stage 2 : Programming the light

function for the hand transmitter

Press button .

"2" appears in the display.

Note: If no 4-minute light is to be programmed,

repress button . The display shows "0" -

programming is completed.

Press the second button on the hand

transmitter, with which the 4-minute light is to

be switched on.

As soon as the code has been read, the red

point display (a) flashes five times before

quitting.

After the code has been learned, briefly press

button .

"0" appears indicating that you have come to

the end of the menu.

1414

1515

1616

1818

1717

2121

1919

2020

Checking the force limit facility

- Place an obstruction (e. g. operator's

cardboard box) underneath the door's

cosing edge.

- Starting from the OPEN end-of-travel

position, actuate the door to close.

- The door travels towards the obstruction,

stops and travels back to the top end-of-

travel position.

- The point display (a) must switch off for

approx. 1 second. Then the operator

functions as normal again.

If the door springs have been changed or

altered, then the force learning cycle must be

repeated:

Proceed to menu stage 5 and keep button

Pressed for 3 seconds. "0" appears in the

display. Then complete the force learning cycle

as explained under point 18a.

Special settings

Menu stage 7: Light phases

Press button for 3 seconds.

"3" appears in the display.

Press button several times until menu

stage 6 is shown.

Keep button pressed again for 3 seconds

until "7" appears in the display.

Menu Light phase Warning

value phase

If the warning phase is set, the light flashes

before the door starts to move and during the

actual travel cycle. The factory setting is 1.

Menu stage 8: "Soft" start and "soft" stop ("soft"

runs)

Press button . "8" appears in the display.

These values correspond to the "soft" runs

measured in cm at the carriage.

Important note:

The factory setting of 4 must be adhered to.

The "soft" runs may only be altered on the

express permission of the door manufacturer.

Press button . "0" appears in the display.

0 60 s -

1 90 s -

2 120 s -

3 240 s -

4 0 s 3 s

5 90 s 3 s

6 240 s 3 s

7 0 s 10 s

8 90 s 10 s

9 240 s 10 s

Menu Start Stop Start Stop

Value Open Open Close Close

0 0 0 0 0

1 15 0 15 0

2 0 15 0 60

3 15 15 15 35

4 25 45 25 45

5 15 15 15 60

6 15 15 15 15

7 35 35 35 50

8 60 15 15 85

9 soft run only

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 553 in the language / languages: English, Dutch, French, Spanish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm Novomatic 553 Manual

Product: