709099

Novoferm Novomatic 413 Manual

19
Zoom out
Zoom in
Previous page
1/45
Next page
GB
• Trouble-shooting
Important note: When working on the operator, always pull out the mains plug beforehand!!!
• Diagnosticdisplay
Duringoperation,thedisplayprovidesdiagnosticinformationonanypossiblefaults/malfunctions
Fault/Malfunction Possiblecause Remedy
Have door checked.
Change force setting (menu stages 5 and 6)
Reset end-of-travel positions (menu stages 3
and 4)
Replace battery in hand transmitter
Plug in/align aerial
Connect external aerial (accessory)
See diagnostic display
Replace battery in hand transmitter
Plug in/align aerial
Programme hand transmitter (menu stage 1)
Remove obstruction or reset CLOSE end-of-
travel position (menu stage 4)
Reset end-of-travel positions (menu stages 3
and 4)
Insufficient range of hand transmitter
Door does not respond to impulse from
hand transmitter or ot other impulse
generators
Door does not respond to impulse from
hand transmitter but does respond to
push-button or other impulse generators
After closing, door opens again to
produce a slight gap
Door presses into the end-of-travel
positions
Door does not fully close/open
Door mechanics have changed
Set closing/opening force too weak.
End-of-travel positions incorrectly set
Door blocks just before CLOSE position
Flat battery in the hand transmitter
Aerial not plugged in/aligned
On-site screening of receiving signal
See diagnostic display
Flat battery in hand transmitter
Aerial not plugged in/aligned
No hand transmitter programmed
Optimum setting of end-of-travel positions has
not been achieved
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
NumberState Diagnosis/Remedy
_______________________________________________________________________________________________________________________
Caution:
Operator starts up and “0” goes out. Operator receives a start impulse at the START input or via a receiver,
normal operation.
0 displayed during the next opening and closing cycle Operator is carrying out a learning cycle for the force limit.
and then goes out. During these travel cycles the force is not monitored!
0 continues to be displayed.
Door neither opens nor closes. STOP A connection is interrupted.
External safety device has been activated (e.g. wicket door).
Door no longer closes. STOP B connection is interrupted.
External safety device has been activated (e.g. photocell).
Permanent impulse signal at the start input. Door no longer accepts a start impulse. External impulse generator emits a
permanent impulse signal (e.g. button is jammed)
An error ocurred in setting the operator. Travel path too long.
Repeat setting procedure (menu stages 3 and 4).
F (menu stages 3 and 4)
Door neither opens nor closes.
Motor has come to a standstil. Motor does not rotate. Call in a specialist company.
V
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Top end-of-travel position Open has been reached.
Bottom end-of-travel position Closed has been reached.
Gate end position has not been reached.
Force-learning cycle not completed. Must be repeated.
Too much pressure in the gate's end-of-travel positions. Gate setting required.
Gate setting und learning cycle not correctly finalized. Repeat gate setting in menus 3 & 4 and complete force-learning cycle
subsequently.
ault during learning cycle. Repeat position learning cycle.
Reduce force when approaching the end-of-travel positions.
Fault during self-test. Disconnect power supply.
Electronic brake activated. Pull drive from top end-of-travel position.
Garage light remains on. Check gate and springs. Set top end-of-travel position lower.
acation lock activated, gate does not open. Slide switch at SafeControl / Signal 112 confirmed. Reset required.
Deletingradiocodes
Restoring factory setting
Press oval key. Keep key pressed while inserting power plug.
All radio codes stored in the hand-held transmitter are now deleted.
Press Open and Close keys at the same time. Keep keys pressed for approx. 3 sec while inserting
power plug.
The factory setting has been restored.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm Novomatic 413 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 413 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info