Manual Novoferm Novomatic 413 (page 18 of 45) (English, German, Dutch, French, Spanish)

709099

Zoom out

Zoom in

1/45

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

• OperatingInstructions

These Operating Instructions describe how to use

the prodct properly and safely. The safety advice and

information as well as the accident prevention and

general safety regulations for the field of application

must be complied with.

(factory-set operating mode)

The garage door operator can be actuated by an

impulse generator such as hand transmitter, key

switch etc. It is only necessary to generate a short,

sharp impulse.

Operator starts up and causes the door to travel to

set open or closed travel limits.

The door stops.

Door continues to move but in opposite direction .

During adjustments, in the event of a power failure or

malfunctions, the door can be disengaged from the

operator by actuating the pull cord on the carriage

and then be operated manually.

If the door is to be operated manually over a longer

period of time, then the existing locking pin must be

inserted (see figure ). The door latches put out of

service for power operation must be refitted,

otherwise the door is not latched in the the closed

position.

In order to restore power operation, return the

locking pin to the parking position ( ) and put the

latches out of service.

After an impulse has been generated, the door

automatically latches with the door operator.

If the closing door encounters an obstruction, the

operator stops and causes the door to open to ist top

end-of-travel position in order to clear the

obstruction. During the last 2 seconds of the closing

cycle, the door only opens slightly, this being

sufficient to clear the obstruction but otherwise

preventing anyone from taking a look into the

garage.

If the opening door encounters an obstruction, the

operator stops immediately and reverses the

travelling direction for approx. one second.

Connection plan ( figure )

Wicket door contact STOPA

An open wicket door stops the operator immediately

or prevents it from starting up.

Light barrier (STOPB)

An interruption of the light barrier causes a stopping

and a reversal during the closing cycle.An

All persons using the gate system

mustbe shown how to operate it

properly andsafely.

Keep hand transmitters out of the reach

of children.

When the operator is being used, the

opening and closing phases must be

monitored. It must be ensured that

neither persons nor objects are located

within the gate’s range of travel.

• Normal operation (0)

Functional sequence

• Quick release

• Internalsafetydevice

• External safety device

First impulse:

Impulse generated while door is moving:

Repeated impulse:

• Maintenance/Checks

The door system must be inspected

and tested by a specialist company

prior to initial operation and at least

once a year thereafter.

Monitoring the force limit

Caution!

The operator control unit features a dual-processor

safety system to monitor the force limit.

The integral force cut-out is automatically tested at

each travel limit.

The door system must be checked prior to initial

operation and at least once a year thereafter. In the

process, the force limiting device (figure 21) must be

tested!

If the closing force is set too

high, persons can be placed at risk of

injury or property could sustain damage.

Tthe force limit for the opening cycle can be adjusted

in menu stage 5, the force limit for the closing cycle

can be adjusted in menu stage 6.

The cycle counters stores the number of opening or

closing cycles performed by the operator.

In order to read out the meter, keep the

button pressed for 3 seconds until a number is

displayed. The display throws out the values

beginning from the highest decimal place down to

the lowest one after another. In the end, a horizontal

line is displayed. Example: 3456 cycles, 3 4 5 6 -

• Cycle counter

interruption of the light barrier during the opening

cycle makes no difference.

The lighting switches on automatically whenever a

start impulse is generated and switches off again

after the set time phase (factory setting approx. 60

seconds).

If a signal light for signalling the opening and closing

phases is installed, this flashes along with the lamp

in the operator as soon as a start impulse is

generated. The operator starts with a time delay in

accordance with the set warning phase (see menu

stage 7).

Programming further hand transmitters:

See menu stages 1 and 2 (figure 15 and 16).

In menu 9, another operating mode can be chosen.

For the setting applying to menu 9, see parantheses.

• Lighting

• Signal light

• Hand transmitter

• Further operating modes

•

Normal operation for ventilation position (1)

Operation on a side-opening sectional door (2)

The ventilation position is designed to allow

ventilation of the garage. For this, the door is opened

approx. 10 cm.

Actuation as for normal operation. By pressing the

2 button on the hand transmitter or generating an

impulse via another device, the door can be brought

into the ventilation position from the open or closed

state.

The gate will close automatically after 60 min or can

be closed earlier by any impulse transmitter.

Instead of opening the door fully, the door can be

partially opened by approx. 1 m in order to provide

access to the garage.

By pressing the 2 button on the hand transmitter or

generating an impulse via another device, the door

can be brought into the partially open state from any

given position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 413 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm Novomatic 413 Manual

Product: