474197
15
Zoom out
Zoom in
Previous page
1/32
Next page
These Installation, Operating and Maintenance Instructions must be retained and kept safe throughout the product’s entire service life.
GB
Trouble-shooting
Important note: When working on the operator, always pull out the mains plug beforehand!!!
Diagnostic display
During operation, the display provides diagnostic information on any possible faults / malfunctions
Fault/Malfunction Possible cause Remedy
Have door checked.
Change force setting (menu stages 5 and 6)
Reset end-of-travel positions (menu stages 3
and 4)
Replace battery in hand transmitter
Plug in/align aerial
Connect external aerial (accessory)
See diagnostic display
Replace battery in hand transmitter
Plug in/align aerial
Programme hand transmitter (menu stage 1)
Remove obstruction or reset CLOSE end-of-
travel position (menu stage 4)
Reset end-of-travel positions (menu stages 3
and 4)
Insufficient range of hand transmitter
Door does not respond to impulse from
hand transmitter or ot other impulse
generators
Door does not respond to impulse from
hand transmitter but does respond to
push-button or other impulse generators
After closing, door opens again to
produce a slight gap
Door presses into the end-of-travel
positions
Door does not fully close/open
Door mechanics have changed
Set closing/opening force too weak.
End-of-travel positions incorrectly set
Door blocks just before CLOSE position
Flat battery in the hand transmitter
Aerial not plugged in/aligned
On-site screening of receiving signal
See diagnostic display
Flat battery in hand transmitter
Aerial not plugged in/aligned
No hand transmitter programmed
Optimum setting of end-of-travel positions has
not been achieved
State
Operator starts up and “0” goes out.
Door neither opens nor closes.
Door no longer closes
Motor has come to a standstil
Permanent impulse signal at the start input
An error has occurred in setting the operator.
“0” displayed during the next opening and
closing cycle and then goes out.
“0” continues to be displayed.
Diagnosis / Remedy
Operator receives a start impulse at the START input or via a receiver,
normal operation.
STOP A connection is interrupted.
External safety device has been activated (e.g. wicket door).
STOP B connection is interrupted.
External safety device has been activated (e.g. Photocell).
Motor does not rotate. Call in a specialist company.
Door no longer accepts a start impulse. External impulse generator
emits a permanent impulse signal (e.g. Button is jammed)
Travel path too long.
Repeat setting procedure (menu stages 3 and 4)
Operator is carrying out a learning cycle for the force limit.
Caution: During these travel cycles the force is not monitored !
Check door mechanics. Door is too sluggish.
Number
0
1
2
3
4
5
0
Subject to changes
Terms of the Guarantee
We shall not bear the costs for dismantling
and installation, freight and carriage. If a
complaint is proven to be unjustified, the
customer must bear our costs.
This guarantee is only valid in conjunction
with the signed invoice and commences on
the day of delivery. The manufacturer
guarantees that the product is free of defects.
The warranty is granted for a period of 24
months, in as far as the verification overleaf
has been properly filled out. Otherwise the
warranty shall expire 27 months after the date
of manufacture.
Any alterations or modifications carried out to
the operator and accessory parts by the
customer. The same shall also apply for
damage incurred during transit or as a result of
force majeure, external influences or natural
wear as well as special atmospherical
stresses. We cannot accept any liability
following alterations or modifications of
functional parts carried out by the customer.
We must be notified of any defects
immediately in writing; on request the parts in
question are to be made available to us.
Dear customer,
During production the garage door operator
you have purchased has undergone various
checks by the manufacturer to ensure that it
is of impeccable quality. Should this operator
or parts of it prove to be of no use or limited
use as a result of proven material or
manufacturing defects, we shall rectify this,
at our discretion, through free-of-charge
repair or replacement.
We shall not accept any liability for damage
as a result of unsatisfactory fitting and
installation, improper putting into service,
incorrect operation and maintenance,
excessive use and overloading as well as
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm Novomatic 403 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 403 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 12,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm Novomatic 403

Novoferm Novomatic 403 User Manual - English, Dutch, French, Spanish - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info