Manual Novoferm DuoPort 700 h-c (page 8 of 20) (English, German, Dutch, French)

709199

Zoom out

Zoom in

1/20

GB "DuoPort 700" double leaf hinged door

Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door!

- 8 -

Assembly

M1 Remove transport profile underneath the sill.

M2 Mount handle on the active leaf [1.20a].

M3 Lay tools out in the garage depending on accessibility and

type of rebate.

M4 Place door behind or into the installation opening accord-

ing to the intended opening direction and secure it so that

it cannot fall over [1.20b].

M5 If the screw-in anchors included in the delivery are used,

screw them into the wide groove on the outside of the

frame profile according to the installation direction.

Number and position according to [1.25a].

M6 Align the vertical frame bars vertically and the frame

crossbar horizontally, and measure the diagonals as a

check [1.25b].

M7 Fastening

M7a If screw-in anchors (AS) are used:

Bend screw-in anchors at the provided kink points up

to the wall surface, drill dowel holes and fasten an-

chors with the aid of suitable dowels [1.30a].

M7b In case of direct assembly with frame plug dowels

(AS):

Open door leaf, secure it so that it cannot be moved

accidentally, first drill through the frame with metal

drill Ø10 in the frame on the score line, then drill dow-

el holes in the masonry with stone drill Ø10, number

and position according to [1.30b].

Clean drill holes, insert/drive dowel plug through the

frame into the drill hole, insert pressure-proof filling

material under the frame at the fastening points to-

wards the wall, apply assembly torque with the aid of

a screwdriver, alternatively a cordless screwdriver

with screwdriver bit PZ 3, attach caps [1.30b].

M8 Fasten sill in the groove, number and position according to

[1.30b], use screws min. Ø 3.5 mm plus appropriate dowel

plug according to floor properties.

Ensure that the sill does not sag or bulge upwards if the

floor is uneven, insert pressure-proof filling material at the

fastening points if necessary.

Insert threshold seal (AS), cut it off at a suitable length,

making sure not to stretch it.

M9 Gap dimension/hinge adjustment:

The hinges can be adjusted in three directions:

M9a Height adjustment +3/-2 mm by turning the adjust-

ment spindle in the frame hinge part with an Allen key

SW 6 [1.35a].

The zero position of height adjustment is reached

when the lower edge of the collar of the eccentric

bush is level with the upper edge of the frame hinge

part.

M9b Side adjustment ± 2.5 mm by turning the stud in the

leaf hinge part with an Allen key SW 4 with a spheri-

cal head [1.35b].

M9c Compression adjustment ± 0.5 mm (usually not nec-

essary) by turning the eccentric bush in the frame

hinge part by 90° clockwise/counter-clockwise, only

possible when door leaf is unhinged.

Adjust the vertical and horizontal gap dimensions between

leaves and frame evenly to 6 ± 1 mm, the horizontal gap

between leaves and upper-edge finished floor to

11 ± 1 mm and the vertical centre gap to 6 + 1 mm by ad-

justing the hinges [1.35c].

M10 Final assembly of the hinges

After adjusting the tension bolt (AS), insert it into the

groove of the leaf section cover (AS), clip on leaf section

cover, clip plastic covers (AS) onto the top and bottom of

the hinges, with the door leaves open,

screw cylinder screw M4x14 (AS) with the aid of Allen

key SW 3 in to the back of the leaf section, thus securing

the tension bolt [1.40a+b].

M11 Insert logo clip into the two holes of the right leaf as seen

from the outside at the bottom on the right.

M12 Seal wall connections and sill connection with a perma-

nently elastic material.

M13 Install locking device(s) as described in the separate instal-

lation instructions.

Test instruction

All parts must be assembled as described in the installation

instructions to assure the functional reliability, durability and

smooth operation of the hinged door. If the door still does not

function properly, please check the following points:

P1 Is the frame installed at right angles and vertically (meas-

ure diagonals) and securely fastened?

P2 Are the gap dimensions observed or correctly adjusted?

[1.35c]. Align the door leaves and correct the gap dimen-

sions using the hinge adjustment function as described in

M9.

P3 Do the latch, deadbolts bolt and flush bolts engage correct-

ly in their strike plates?

Rework the recess in the strike plate of the latch opening

or grease the latch, if necessary.

P4 Handle set function: Handle must be kept a horizontal

position by the holding spring when it is not being operat-

ed.

P5 Are locking devices for the open end position of the leaves

installed and functional?

Disassembly instructions

- Disassembly by qualified installers only -

Please read these instructions carefully prior to disassem-

bly!

The following tools are required for disassembly:

Allen key SW 3 and SW 6, Phillips screwdriver PH 2 and PZ 3,

hammer and metal saw, if necessary, ...

Disassembly:

Disassembly is basically carried out in the reverse order of the

assembly steps.

D1 Disassemble locking devices.

D2 Door leaf disassembly

D2a If there is sufficient assembly clearance ( ≥ 35 mm )

from the header of the installation opening over the

upper edges of the leaves, the leaves can be un-

hinged from the frame by lifting them when they are

open.

D2b In case of assembly clearance < 35 mm, first remove

all leaf section covers in the reverse order of assem-

bly step M10 with the leaves open. Remove the cylin-

der screw from the leaf hinge section with Allen key

SW 3, push the tension bolt out of its guide from be-

hind with the wrench key, remove the leaf section

cover and put small parts aside.

Then insert wedges under the leaves while they are

open and secure them so that they cannot fall over,

loosen and remove the screws of the leaf sections

with wrench key SW 6, twist the detached hinge leaf

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm DuoPort 700 h-c in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm DuoPort 700 h-c

Novoferm DuoPort 700 h-c Additional guide - All languages - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm DuoPort 700 h-c Manual

Product: