296277
44
Zoom out
Zoom in
Previous page
1/56
Next page
Model 9000/9100/9500
44
Troubleshooting
PROBLEM CAUSE CORRECTION
1. Softener fails to regenerate. A. Electrical service to unit has been
interrupted.
B. Timer is defective.
A. Assure permanent electrical
service (check fuse, plug, pull
chain or switch).
B. Replace timer.
2. Hard water. A. Bypass valve is open.
B. No salt in brine tank.
C. Injector screen plugged.
D. Insufficient water flowing into brine
tank.
E. Hot water tank hardness.
F. Leak at distributor tube.
G. Internal valve leak.
A. Close bypass valve.
B. Add Salt to brine tank and maintain
salt level above water level.
C. Clean injector screen.
D. Check brine tank fill time and clean
brine line flow control if plugged.
E. Repeated flushing of the hot water
tank is required.
F. Make sure distributor tube is not
cracked. Check O-Ring and tube
pilot.
D. Replace seals and spacers and/or
piston.
3. Unit used too much salt. A. Improper salt setting.
B. Excessive water in brine tank.
A. Check salt usage and salt setting.
B. See Problem No. 7.
4. Loss of water pressure. A. Iron buildup in line to water
conditioner.
B. Iron buildup in water conditioner.
C. Inlet of control plugged due to
foreign material broken loose from
pipe by recent work done on
plumbing system.
A. Clean line to water conditioner.
B. Clean control and add mineral
cleaner to mineral bed. Increase
frequency of regeneration and/or
backwash time.
C. Remove pistons and clean control.
5. Loss of mineral through drain line. A. Air in water system.
B. Drain line flow control too large.
A. Assure that well system has
proper air eliminator control.
Check for dry well condition.
B. Check to ensure drain line flow
control is sized properly for your
mineral tank.
6. Iron in conditioned water. A. Fouled mineral bed. A. Check backwash, brine draw and
brine tank fill. Increase frequency
of regeneration.
7. Excessive water in brine tank. A. Plugged drain line flow control.
B. Plugged injector system.
C. Timer not cycling.
D. Foreign material in brine valve.
E. Foreign material in brine line flow
control.
F. Power loss during brine fill.
A. Check flow control.
B. Clean injector and screen.
C. Replace timer.
D. Replace brine valve seat and clean
valve.
E. Clean brine line flow control.
F. Check power source.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nokia 9500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nokia 9500 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nokia 9500

Nokia 9500 User Manual - Dutch - 119 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info