Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly.
Batteries should be installed by Nilfi sk or by a qualifi ed electrician.
1 Remove the batteries from their shipping crate and carefully inspect them for cracks or other damage. If damage is evident, contact the
carrier that delivered them or the battery manufacturer to fi le a damage claim.
2 Turn the Power Switch (B) OFF and remove the magnetic key.
3 Raise the steering column to the full upright position. Tip the seat forward and engage the Seat Prop Rod (9).
4 Remove the crossbar and if installed also remove the overhead guard.
5 Remove the recovery tank from the machine. NOTE: Disconnect the recovery switch wiring and the vacuum motor wiring then lift the tank
straight up and off the machine.
6 Your machine comes from the factory with enough battery cables to install six 6 volt batteries. Using at least (2) people and an appropriate
lifting strap, carefully lift the batteries into the battery compartment and arrange them exactly as shown in FIGURE 1. Secure the batteries
as close to the front and right side of the machine as possible. Use battery spacer to keep batteries from moving. If installing a mono-block
battery use an overhead hoist (the seat support bracket will need to be temporarily removed to install a mono-block battery).
7 Install the battery cables as shown. Position the cables so the battery caps can be easily removed for battery service.
IMPORTANT!: The protective caps supplied with the batteries need to be left on or re-used to completely cover the portion of the
battery terminals that are not being protected by the battery cable terminal cover boots supplied with the battery cables. This also
applies to the inline fuse holder boot.
8 Carefully tighten the nut in each battery terminal until the terminal will not turn. Do not over-tighten the terminals, or they will be very diffi cult
to remove for future service.
9 Coat the terminals with spray-on battery terminal coating (available at most auto parts stores).
10 Put one of the black rubber boots over each of the terminals and connect the Machine Battery Connector (10).
11 Make sure the Fuse Holder Boot (14) is covering the fuse holder, the cable end of the Machine Battery Connector (10), and as much of the
battery terminal as possible. Leave the protective caps supplied with the batteries in place or re-use to cover the terminal areas not protected
by the terminal cover boots.
When changing batteries or the charger, please contact your local authorized service center for correct battery, charger and machine
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Nilfisk SC6000 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Nilfisk SC6000 in the language / languages: English as an attachment in your email.
The manual is 29.64 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
