787649
84
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH INSTRUCTIONS FOR USE
26 SC2000 - 9100000383 01/2015
revised 07/2017
TROUBLESHOOTING
TROUBLE POSSIBLE CAUSE REMEDY
The motors are not operating; the display (51) and
button LEDs do not turn on.
The battery connector is disconnected. Connect.
The batteries are completely discharged. Charge the batteries.
The machine does not move and the display (51)
shows the alarm:
WARNING ALARM T3
Machine turned on with pedal pressed. Release the drive pedal.
If the problem persists, contact an authorised
Service Center.
At machine start-up, the button (43) LED ashes
and the brushes do not work.
Machine switched off without rst raising the
brush deck.
Wait for the deck to raise before turning the
brushes on again by pressing the switch.
The brush does not operate; the battery symbol
(51-C) border ashes and the display shows the
alarm message:
WARNING ALARM G4
The batteries are discharged. Charge the batteries.
If the problem persists, replace the batteries.
When working, the display shows the alarm
message: WARNING ALARM F2
Brush motor overload. Use a different/less aggressive brush and/or
avoid working with extra pressure turned on.
There are foreign materials (tangled threads,
etc.) preventing the brush from rotating.
Clean the brush hub.
The display (51) shows the alarm message:
WARNING ALARM T2
Drive motor overload. Turn off the machine and then turn it on again.
Avoid using the machine on slopes greater
than those indicated or going over excessively
tall obstacles.
While recharging the batteries with the on-board
battery charger, the display (51) shows the alarm
message:
WARNING ALARM C4 or C5
Battery charger not able to correctly recharge
the batteries within the maximum time.
Run the battery charging cycle again.
If the problem persists, replace the batteries.
The display (51) shows an alarm message of the
following type:
WARNING ALARM XX
Where “XX” is a code other than those listed
above.
The machine electronic control system is in
alarm condition.
Turn off the machine and then turn it on again.
If the problem persists, contact an authorised
Service Center.
The display (51) shows the alarm message:
INVALID SMART KEY
The user key is not enabled. Add the speci c user key to the list of enabled
user keys.
The dirty water vacuuming is insuf cient. The recovery tank is full. Empty the tank.
The vacuum grid is clogged or the oat is
stuck closed.
Clean the vacuum grid.
Debris collection lter container clogged. Clean.
The hose is disconnected from the squeegee. Connect.
The squeegee is dirty or the squeegee blades
are worn or damaged.
Clean the squeegee or overturn/replace the
blades.
The tank cover is not properly closed, or the
gasket is damaged.
Correctly close the cover or clean/replace the
gasket.
The solution ow is insuf cient. Empty detergent solution tank. Re ll.
The solution lter is dirty. Clean the lter.
The EcoFlex system tank (optional) is dirty/
encrusted.
Clean with the drain cycle.
The squeegee leaves marks on the oor. There is debris under the squeegee blades. Remove the debris.
The squeegee blades are worn, chipped or
torn.
Overturn or replace the blades.
The squeegee has not been balanced with the
handwheel.
Adjust the squeegee.
NOTE
If the machine has been purchased with an on-board battery charger, the machine cannot operate if this device is not on
board. In case of battery charger malfunction, contact an authorised Service Center.
For any further information, contact Nil sk Service Centres.
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk SC2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk SC2000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info