787649

Nilfisk SC2000 Manual

83
Zoom out
Zoom in
Previous page
1/116
Next page
INSTRUCTIONS FOR USE ENGLISH
9100000383 - SC2000 25
01/2015
revised 07/2017
DRAINING THE ECOFLEX SYSTEM
(For machines with EcoFlex system)
Clean the detergent tank as shown in the previous section.
To remove residual detergent from the detergent hoses and pump, proceed as follows.
1. Place the user key (52) in the key reader (41), then press the push-button (42) to start the machine.
2. Check that the detergent quantity indicator (50-G) on the display has at least one segment lit.
3. Press and hold buttons (46) and (47) at the same time until screen (50-N) appears on the display (after approximately 5
seconds).
4. Release buttons (46) and (47) and wait for the countdown timer on the display to fi nish and the vacuum system to be activated.
5. Collect the detergent remained on the fl oor.
6. Turn off the machine with the push-button (42) and remove the user key (52).
7. Lift the recovery tank assembly (17), then check that the detergent tank hose (38) is empty, otherwise perform steps 3 to 7
again.
NOTE
The draining cycle lasts about 30 seconds, then the vacuum function automatically turns on, which allows to remove the
detergent remained.
The draining cycle can also be performed with the detergent tank (38) full of water, thus cleaning the system thoroughly.
It is advisable to perform this type of draining to clean the EcoFlex system from dirt and deposits if the machine has not
been used/cleaned for a long time.
The draining cycle can also be performed to quickly fi ll the detergent supply hose when the tank (38) is full but the
system is still empty.
If necessary, the draining cycle can be performed several times in succession.
FUSE CHECK/REPLACEMENT
NOTE
All machine electrical circuits are protected by auto-resettable electronic devices. The safety fuses activates only in case
of serious damage.
It is recommended to have the fuses replaced by qualifi ed personnel only.
Refer to the Service Manual available at any Nilfi sk Retailer.
SAFETY FUNCTIONS
The machine is equipped with the following safety functions.
EMERGENCY PUSH-BUTTON
The emergency push-button (5) is located in an easily accessible position. Press it fi rmly in case of immediate necessity to stop all
machine functions.
To reset the machine operation, lift the recovery tank assembly (17) and reconnect the battery connector (6).
ANTI-SKID SAFETY SYSTEM
This system reduces the speed when turning and when the machine tilts laterally to avoid sudden skids, this increasing the machine
stability in any condition. The system activation is shown by the icon (51-J) on the display.
DRIVER’S SEAT MICROSWITCH
It is located inside the driver’s seat (12) and it does not allow the machine drive system to operate if the operator is not seated on
the driver’s seat.
ELECTROMAGNETIC BRAKE
It is built-in the rear driving wheels (24) and keeps the machine braked when the machine is off or stopped.
… 83 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk SC2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk SC2000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info