Manual Nilfisk IV150 (page 37 of 60) (English, German, Dutch, French)

19480

Zoom out

Zoom in

1/60

INSTRUCTIONS FOR USE

32401106(1)2004-04 A 7

USING THE VACUUM

Correct use of the vacuum

Before using the machine, connect the suction pipe to the

inlet.

Keep long suction pipes as straight as possible.

Do not allow them to bend or twist as this will cause

excessive wear and clogging.

When the vacuum is powered, suction is created at the

pipe inlet and this sucks in the waste material.

This waste material passes through the pipe and

accessories through the inlet “4” until it reaches container

“6”, where a deflector “5” in the filtering chamber subjects

it to a centrifugal action causing the heavier solids to

deposit on the bottom of container “6”.

The primary filter will retain the lighter particles in the

airflow “3” as the air passes through it.

Lastly, the filtered air enters impeller “1” of the suction unit,

it is then exhausted through exhaust panel “2”.

Cleaning the primary filter

Vacuum gauge “1” is installed on the front part of the

vacuum (see fig. 4) and indicates the vacuum created

within the vacuum itself. This vacuum is expressed in

millimetres of water column. If the pointer is on the right

(green area), the filter will be in a good condition.

If the pointer swings to the left (red area), this means that

the filter is clogged and has a reduced filtering capacity.

In this case, it will be necessary to clean the primary filter.

Switch off the vacuum by pressing the OFF button “5” (red)

(fig. 4).

Operate the filter shaker handle “2” (fig. 7) several times in

order to detach the dust from the filter.

Wait a few minutes for the dust to deposit at the bottom of

the container, then empty this.

Clean the pipe, if this is the case.

Emptying the container

Check the amount of waste in the container according to

the job in hand and to prevent it from becoming

excessively full.

Before emptying container “1”, first switch off the vacuum

by pressing the OFF button (red) then turn the main switch

to position 0 (OFF).

It is also advisable to clean the primary filter by using the

shaker handle.

Wait a few minutes for the dust to detach from the filter and

deposit in container “1”.

Lift lever “4” under the inlet.

Container “1” will lower until it rests with its wheels on the

floor.

Grip handle “2” and remove the container, then empty out

its contents.

To make container “1” easier to empty, Nilfisk-Advance

supplies a lifting strap to be used when lifting the container

by use of a forklift or a crane. Insert the strap in the

mounting brackets on the container.

To remount the container, fit it under filter unit “5”.

Now push lever “4” downwards, allowing container “1” to

lift until it seals against filter chamber “5”.

To facilitate the container emptying and cleaning

operations, it is advisable to use plastic bags “1” as

indicated in figure 9.

ATTENTION!

If the machine is used for fluids or wet

materials and fluid emerges from it, the

machine must be immediately switched-off,

cleaned and dried and all filters replaced.

NOTE

If the vacuum gauge “1” (fig. 7) is still in the

red area, the suction pipe, may be clogged,

and not the filter.

ATTENTION!

The container must not be emptied if it

contains dust classified as a health threat,

(Dust classifications M and H).

A plastic bag must be used for the disposal

of dangerous dust or, alternatively, the ABS

container with a lid.

The corresponding article numbers for

these items are given in Chapter 9.

ATTENTION!

Check that when back in position, container

“1” is in a perfectly sealed condition.

ATTENTION!

These bags cannot be used when the waste

contains liquids or sharp items.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk IV150 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk IV150

Nilfisk IV150 User Manual - Italian, Portuguese, Spanish - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nilfisk IV150 Manual

Product: