454224
31
Zoom out
Zoom in
Previous page
1/48
Next page
ENGLISH / B-9
FORM NO. - 56041703 - BA 625, BA 725, BA 825 - B-9
BATTERIES
If your machine shipped with batteries installed do the following:
Check that the batteries are connected to the machine  (25 / 25a).
Turn ON the Key Switch  (A) and check the Battery Indicator (D5). If the gauge is completely lled, the batteries are ready for use. If the gauge
is less than full, the batteries should be charged before use. See the “Charging The Batteries” section.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS
REGARDING SETTING THE CHARGER FOR BATTERY TYPE (SEE CHART).
See TSBUS2007-979 for the latest battery charger algorithms.
If your machine shipped without batteries installed do the following:
Consult your Authorized Nil sk dealer for recommended batteries.
Install the batteries by following the instructions below.
DO NOT install two 12 volt batteries in your machine. This affects the stability of the machine.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS
REGARDING SETTING THE CHARGER FOR BATTERY TYPE (SEE CHART).
See TSBUS2007-979 for the latest battery charger algorithms.
WARNING!
Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin
or eyes. Explosive hydrogen gas is vented from the batteries through openings in the battery caps. This gas can be ignited by any
electrical arc, spark or ame. Do not install any lead-acid battery in a sealed container or enclosure. Hydrogen gas from overcharging
must be allowed to escape.
FIGURE 1
revised 10/08
When Servicing Batteries...
* Remove all jewelry
* Do not smoke
* Wear safety glasses, rubber gloves and a rubber apron
* Work in a well-ventilated area
* Do not allow tools to touch more than one battery terminal at a time
* ALWAYS disconnect the negative (ground) cable rst when replacing batteries to
prevent sparks.
* ALWAYS connect the negative cable last when installing batteries.
CAUTION!
Electrical components in this machine can be severely damaged if the batteries
are not installed and connected properly. Nil sk, a quali ed electrician, or the
battery manufacturer should install batteries.
1 Remove the batteries from their shipping crate and carefully inspect them for
cracks or other damage. If damage is evident, contact the carrier that delivered
them or the battery manufacturer to le a damage claim.
2 Turn the Master Key Switch (A) OFF and remove the key.
3 Tip the recovery tank to the side, locked position. Remove the battery cables from
inside the battery compartment.
4 Your machine comes from the factory with enough battery cables to install four 6
volt batteries. Carefully lift the batteries into the battery compartment and arrange
them exactly as shown in FIGURE 1. Secure the batteries as close to the back of
the machine as possible.
5 Install the battery cables as shown. Position the cables so the battery caps can
be easily removed for battery service.
6 Carefully tighten the nut in each battery terminal until the terminal will not turn.
Do not over-tighten the terminals, or they will be very dif cult to remove for future
service.
7 Coat the terminals with spray-on battery terminal coating (available at most auto
parts stores).
8 Put one of the black rubber boots over each of the terminals and connect the
Battery Pack Connector (25 / 25a).
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk BA 825 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk BA 825 in the language / languages: English, Turkish as an attachment in your email.

The manual is 5,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info