609423
62
Zoom out
Zoom in
Previous page
1/84
Next page
ENGLISH INSTRUCTIONS FOR USE
20 SCRUBTEC 337.2 - 9099872000
TROUBLESHOOTING
Trouble Possible Cause Remedy
The motors do not turn on; no LED
turns on.
The battery connector is disconnected. Connect.
The battery is completely discharged.
Contact Nilsk Service Center to restore the
battery or to replace it.
The fuse F3 is open. Replace.
The brush motor does not run. The F1 fuse has triggered. Reset the fuse.
The vacuum system motor does not
turn on.
The fuse F2 is open. Replace.
The dirty water vacuuming is
insufcient.
The recovery tank is full. Empty.
The vacuum grid is clogged or the oat is stuck
closed.
Clean the grid and check the oat.
The vacuum hose is disconnected from the squeegee
or faulty.
Connect or replace. (*)
The squeegee is dirty or the squeegee blades are
worn or damaged.
Clean the squeegee or replace the blades.
The recovery tank cover is not properly closed, or the
gaskets are damaged.
Check and/or clean the seating surface or replace
the gaskets.
The vacuum system motor lter is dirty. Clean.
The solution ow is insufcient.
The detergent duct is dirty/clogged. Clean.
The solenoid valve is faulty. Replace. (*)
The squeegee leaves marks on the
oor.
There is debris under the squeegee blades. Remove the debris.
The squeegee blades are worn, chipped or torn. Replace the blades.
When connecting the battery charger
to the electrical mains the 3 LEDs on
the handlebar turn on and the battery
does not charge.
The battery is damaged or it is excessively
discharged.
Contact Nilsk Service Center to restore the
battery or to replace it.
When connecting the battery charger
to the electrical mains the yellow LED
on the handlebar ashes and the
battery does not charge.
The battery is not properly connected to the machine
system.
Check the battery connections.
When connecting the battery charger
to the electrical mains the red LED on
the handlebar ashes and the battery
does not charge.
There is a fault in the battery charger. Replace. (*)
When the battery charging procedure
is completed, the red LED on the
handlebar ashes.
The battery has not been fully charged during the
maximum time interval allowed.
Try to repeat the battery charging procedure.
If the problem persists, replace the battery.
(*) This maintenance procedure must be performed by Nilsk authorised Service Center.
NOTE
The machine is inoperative without the battery charger.
In case of battery charger malfunction, contact an authorised Service Center.
For further information refer to the Service Manual, available at any Nilsk Service Center.
SCRAPPING
Have the machine scrapped by a qualied scrapper.
Before scrapping the machine, remove and separate the following materials, which must be disposed of properly according to the
Law in force:
Battery
Brushes
Plastic hoses and components
Electrical and electronic components (*)
(*) Refer to the nearest Nilsk Center especially when scrapping electrical and electronic components.
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO SCRUBTEC 337.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO SCRUBTEC 337.2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info