787629
5
Zoom out
Zoom in
Previous page
1/14
Next page
5
2.0 Operating Instructions EN
2.1 Operating facilities
Start-/stop rotary switch (2).
Spray gun (6) with trigger (6a) and locking device
(6b).
Dosing regulator for detergents (12).
Regulation of pressure / water volume (14) (not
available on model B).
2.2 Connection
1. PRO 130/150/160: Attach the high pressure hose
(5) to the connection for high pressure hose (3).
Only use one extension hose of max. 7 m.
PRO 130/150/160 X-TRA: Unwind the high pres-
sure hose completely.
2. Attach the nipple of the high pressure hose to the
spray gun quick coupling.
3. Mount the nozzle or any other equipment you
want to use.
4. Connect the machine to the water and power
supplies.
2.3 Start
1. Check that the machine is in vertical po si tion.
2. Activate the trigger of the spray gun (6a) and let
the water run out until any air has escaped from
the inlet hose.
3. Turn the start/stop switch (2) to pos. I.
2.4 Operation
1. Always hold the spray lance
rmly with both hands! The spray
lance is affected by a lon gi tu di nal
thrust of up to 26.5 Nm when the
high pressure washer is ope rated.
2. Point the nozzle at the ground!
3. Activate the trigger of the spray gun (6a).
4. Always adjust the distance and thus the pres-
sure of the nozzle to the sur face which is to be
cleaned. NOTE: The pressure can be reg u lat ed
on the TORNADO® PR nozzle or the button for
regulation of pressure / water volume (14).
NOTE: Do not cover the machine during operation. If
the machine is left or not used for 5 minutes, it must
be switched off on the start/stop switch (2) pos. O.
Operation with detergents
Application of detergents is NOT possible if an
extension hose is applied.
1. Fill the container with a detergent.
2. Mount the TORNADO® PR nozzle and adjust it to
low pressure (see section 2.4.4).
3. Adjust the dosing regulator (12) to the re quired
vol ume of detergent (0-5%).
4. Apply the detergent from below and up wards.
5. Let the detergent act for the time stated on the
packing of the detergent and fl ush with pure water.
Separate detergent container
1. Remove the cover with suction hose from the
detergent container.
2. Mount the cover with suction hose on the separate
detergent container.
The cover has a standard thread and fi ts common
detergent containers. If your container does not have
a standard thread, detach the fi lter from the suction
hose and remove the cover. Remount the fi lter in the
suction hose.
Extra detergent hose can be pulled out of the ma-
chine.
2.5 Regulation of pressure / water
volume
This function is not available on model B.
Working pressure and water volume can be regu-
lated on the machine by turning the button for regu-
lation of pressure / water volume (14). The pressure
can be read on the pressure gauge (13).
2.6 Suction mode
The machine can take in water from a rain water
butt as an example. In the suction mode, the inlet
hose must be fi lled with water before starting up the
machine. The water inlet hose must not be too long,
approx. 5 m.
1. Make sure that the water butt is not placed on a
lower level than the ma chine.
2. Attach the water inlet hose to the ma chine and
place the other end of it in the water butt.
High pressure
Low pressure
Downloaded from www.Manualslib.com manuals search engine
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO P 160.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO P 160.1 in the language / languages: English, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk-ALTO P 160.1

Nilfisk-ALTO P 160.1 User Manual - German - 12 pages

Nilfisk-ALTO P 160.1 User Manual - German - 12 pages

Nilfisk-ALTO P 160.1 User Manual - Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info