609109
28
Zoom out
Zoom in
Previous page
1/56
Next page
28 Original Instructions
1. Saw the pipe rectangularly through and take off
burrs.
2.
It will be most easy
for you to saw the
pipe rectangularly
through by means
of the pipe sawing
mechanism shown.
NAME:BAV 6/42
(for pipes of 6-42 mm
OD).
NOTE: Do not use pipe cutter!
The pipe will be cut over slantingly
and there will be burrs inside as
well as outside the pipe end.
3.
Lubricate thread as well as cut-
ting- and key ring with oil (not
grease). Now push the pipe nut
and the ring over the pipe end as
shown on the drawing.
If the cutting- and key ring can-
not or can only just be pushed
over the end of the pipe, do not
entlarge it, but file the pipe end.
Mounting in Connection Socket
A marking thread on
the compression nut
will make it easier for
you to observe the
turns prescribed.
5. (NOTE: The pipe must nut turn at the same
time).
The cutting- and key ring will get hold of the
pipe, and now it is unnecessary to press the pipe
further. For the final feed, give the compression
nut another turn of approximately 3/4. By doing
so, the ring will cut into the pipe and reveal an
apparent belt.
6. Pipes of a large outer diameter and all
connections in free pipings are mounted
in a vice of practical reasons while you
are fastening the connection socket. The
screw spanner must have a length ap-
proximately 15 times as long as the width
of it. (Lengthen it by means of a pipe, if
necessary). Proceed according to point
4.
When using series connection sockets, be
aware that the pipe ends go into
the same inner conus as the one
in which the mounting in the vice
was carried out. The final tightening
will be simplified by loosening the
compression nut a little, so that the
wearing surfaces may be supplied
with a little oil.
7.
After the final feeding, loosen
compression nut and check
that there is an apparent belt
before the cutting. If not - wring
the cutting- and key ring a little
extra.
Apparent belt
8. It does not matter if the cutting- and key
ring can be turned on the pipe end.
9. REMOUNTING
After each loosening of the connection, the
tightening of the compression nut may be
done without any lengthening with a pipe
and without any violent effort.
10.
The straight pipe end,
which goes into the
screwed connection, must
have a length of at least
2 lengths of the compres-
sion nut (H).
If the pipings are longer
or more weighted, you
will have to mount a pipe
fitting.
4. At first screw up the
compression nut by
hand until it has got
contact with the cut-
ting- and key ring.
Then press the pipe
wholly up to the inner
conus and give the
compression nut a
turn of app. 3/4.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO DELTABOOSTER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO DELTABOOSTER in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk-ALTO DELTABOOSTER

Nilfisk-ALTO DELTABOOSTER Additional guide - English - 1 pages

Nilfisk-ALTO DELTABOOSTER Additional guide - German - 1 pages

Nilfisk-ALTO DELTABOOSTER User Manual - German - 56 pages

Nilfisk-ALTO DELTABOOSTER User Manual - Dutch - 62 pages

Nilfisk-ALTO DELTABOOSTER Additional guide - French - 1 pages

Nilfisk-ALTO DELTABOOSTER User Manual - French - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info