619204

Niko 350-20054 Manual

20
Zoom out
Zoom in
Previous page
1/32
Next page
350-20054 / 350-20055
20
EN
Connecting the presence detector (fig. 4 and 5)
- Switch off the mains supply.
Power is supplied from the mains via terminals L
1
and N.
- Connect the lighting via terminals N and (fig. 5.1).
Connect a push button between terminals L and if manual operation of the presence detector is also desired (fig. 5.2).
- Connect the ground wire to terminal .
3. OPERATION AND SETTINGS
3.1. Operation
3.1.1. General
The presence detector is ready to use three to five minutes after connecting to the mains voltage (warm-up time). The
connected lighting will be switched off as soon as the device is ready to use.
3.1.2. Automatic ON
The integrated light sensor continuously measures the light level in the detection zone and compares this level with the
preset value specified using the LUX key. The light sensor automatically switches the lighting on only when the detector
detects motion within the detection range and when the daylight level drops below the preset lux value. The lighting remains
on as long as motion is detected.
The ventilation output of the 2-channel detector is activated, regardless of the daylight level.
3.1.3. Automatic OFF
The lighting automatically switches off when the preset daylight level is reached.
The TIME key is used to set the switch-off delay as desired. The lighting will remain on for the specified delay time after the
last motion is detected. Once the switch-off delay has expired, the lighting will switch off.
Attention: The switch-off delay on channel 1 must be set to at least 5 minutes to ensure that the 25% increase on channel 2
will be activated. If the switch-off delay on channel 1 is less than 5 minutes, channels 1 and 2 will be switched at the same time.
3.1.4. Manual ON/OFF
The lighting can also be manually switched on and off by pressing the 230 Vac NO push button, regardless of the measured
daylight level.
• A long press (> 2 s) on the push button with the lighting switched off, will switch the lighting on. The lighting
will remain on. A short press (< 2 s) on the push button will switch the lighting off. The automatic mode is now activated.
• A short press (< 2 s) on the push button with the lighting automatically switched on, will switch the lighting off.
The automatic mode is reactivated after ten seconds to allow time to leave the detection area.
• A long press (> 2 s) on the push button with the lighting automatically switched on, will switch the lighting off
permanently. The presence detector is now disabled. Press the push button briefly (< 2 s) to switch the lighting on
again. The automatic mode is now activated.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Niko 350-20054 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Niko 350-20054 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info