Manual NetworX NX-148E LCD Keypad (page 17 of 24) (English)

629269

Zoom out

Zoom in

1/24

LCD KEYPAD 17

 [new user code]

      

Prompts for a user number. Repeat steps 3 and 4

if another user code needs to be programmed.

 Keypad will beep 3 times if code is rejected.

 # while display is prompting

for a user number.

      

Exits and saves data.

7m. ASSIGNING AUTHORITY LEVEL

 You must have authority to the partition you wish to add or remove from another person’s authority.

ACTION RESULT

  

      

Prompts “Please Enter Your Code".

 [master code]

      

Prompts for a user number.

 [user code]

2-digit ID if NX-4, NX-4V2, NX-6,

NX-6V2, NX-8, NX-8V2, NX-8-CF

3-digit ID if NX-8E, NX-8E-CF (use

leading zeros!! (i.e.  for user 7)

      

Prompts through the following list of attributes.

Outputs used?

If NO… If YES…

Master code? Output 4 enable?

Sched arm only? Output 3 enable?

Arm only? Output 2 enable?

Reserved Output 1 enable?

Open / Close Rprt?

Bypass enable?

Arm / Disarm?

 [partition number]

      

 Default allows access to ALL partitions.

The first keypress will remove access to the

partition. To reestablish access, press the partition

number again.

 

      

Saves data. Prompts for next user code. Return to

step 3 to program another user code.

 #

      

Exits this mode.

NOTE TO INSTALLER: Any master arm/disarm code can add or change a user code if the master

code has access to the same partitions as the code being added/changed. Consequently, when

programming the user codes for a partitioned system, leave at least one code access to all

partitions or you will not be able to add new users (can be "go to program code" if enabled in

location 43 of the control panel). If you desire the end user to be able to add new codes, you must

remove the partition authority from all blank codes.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NetworX NX-148E LCD Keypad in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NetworX NX-148E LCD Keypad Manual

Product: