519682
109
Zoom out
Zoom in
Previous page
1/134
Next page
| 109
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
To configure a LAN segment using the wireless access point in repeater mode:
1. Configure the wireless access point (AP1 on LAN Segment 1 in Figure 5-9):
a. Select Configuration > WDS.
b. Next to WDS Mode, select the Manual radio button.
c. Click the Edit hyperlink to the right of one of the nodes in the Manual WDS Settings
table.
d. On the Edit WDS screen, in the MAC Address field, enter the MAC address of the
corresponding wireless access points (AP2 on LAN Segment 2).
e. Static WEP is supported. NETGEAR recommends that you configure static WEP to
protect this communication. (You can do so on the Edit WDS screen.)
f. Click Save to Flash & Activate to save and activate your settings.
2. Configure AP2 in LAN segment 2 with the MAC address of its “upstream” wireless access
point (AP1).
3. In addition, configure AP2 with the MAC address of its “downstream” wireless access point
(AP3 in LAN segment 3).
4. Configure AP3 with the MAC address of its “upstream” wireless access point (AP2).
5. Verify the following for all wireless access points:
The LAN network configuration of the wireless access points are configured to
operate in the same LAN network address range as the LAN devices.
All APs must be on the same LAN. That is, the LAN IP addresses of all APs must be
in the same network.
If using DHCP, all wireless access points should be set to obtain an IP address
automatically (as a DHCP client). For more information, see
“Configuring IP Settings”
on page 20.
All wireless access points must use the same channel, authentication mode, and
security settings.
6. Verify connectivity across the LAN.
Note: You can extend the repeating functionality by adding up to two more
wireless access points that are configured in repeater mode.
However, since repeaters communicate in half-duplex mode, the
bandwidth decreases as you add repeaters to the network. Also, you
can extend the range of the wireless network with NETGEAR
wireless antenna accessories.
109


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WGAP150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WGAP150 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WGAP150

Netgear WGAP150 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info