519682
107
Zoom out
Zoom in
Previous page
1/134
Next page
| 107
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
Note: Figure 5-8 shows the WGAP150 with an external antenna, which
does not come standard with the product.
To set up the point to multi-point bridge configuration:
1. Configure the wireless access point (AP1 on LAN Segment 1 in Figure 5-8):
a. Select Configuration > WDS.
b. Next to WDS Mode, select the Manual radio button.
c. Click the Edit hyperlink to the right of one of the nodes in the Manual WDS Settings
table.
d. On the Edit WDS screen, in the MAC Address field, enter the MAC address of the
corresponding wireless access points (AP2 on LAN Segment 2).
e. Static WEP is supported. NETGEAR recommends that you configure static WEP to
protect this communication. (You can do so on the Edit WDS screen.)
f. Click Save to save your settings.
g. Click the Edit hyperlink to the right of another node in the Manual WDS Settings
table.
h. On the Edit WDS screen, in the MAC Address field, enter the MAC address of AP3
on LAN Segment
3 in Figure 5-8 on page 106).
i. Static WEP is supported. NETGEAR recommends that you configure static WEP to
protect this communication. (You can do so on the Edit WDS screen.)
j. Click Save to Flash & Activate to save and activate your settings.
2. Configure AP2 on LAN Segment 2 (see Figure 5-8 on page 106) in point-to-point bridge
mode with the remote MAC address of AP1.
3. Configure AP3 on LAN Segment 3 (see Figure 5-8 on page 106) in point-to-point bridge
mode with the remote MAC address of AP1.
4. Verify the following for all wireless access points:
The LAN network configuration of the wireless access points are configured to
operate in the same LAN network address range as the LAN devices.
Only AP1 on LAN Segment 1 is configured in point-to-multi-point bridge mode, and all
others APs are configured in point-to-point bridge mode.
All point-to-point APs must have AP1’s MAC address in their Manual WDS Settings
table.
All APs must be on the same LAN. That is, the LAN IP addresses of all APs must be
in the same network.
If using DHCP, all wireless access points should be set to obtain an IP address
automatically (as a DHCP client). For more information, see
“Configuring IP Settings”
on page 20.
All wireless access points must use the same channel, authentication mode, and
security settings.
5. Verify connectivity across the LANs:
107


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WGAP150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WGAP150 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WGAP150

Netgear WGAP150 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info