670507
47
Zoom out
Zoom in
Previous page
1/116
Next page
genie Advanced Home
47
N300 Wireless Router JWNR2000v3
LAN Setup Screen Settings
You can configure the following LAN settings:
Device Name. This is the abbreviated name of the modem router.
LAN TCP/IP Setup:
IP Address. The LAN IP address of the router.
IP Subnet Mask. The LAN subnet mask of the router. Combined with the IP address,
the IP subnet mask allows a device to know which other addresses are local to it, and
which must be reached through a gateway or router.
RIP Direction. Router Information Protocol (RIP) allows a router to exchange routing
information with other routers. This setting controls how the router sends and receives
RIP packets. Both is the default setting. With the Both or Out Only setting, the router
broadcasts its routing table periodically. With the Both or In Only setting, the router
incorporates the RIP information that it receives.
RIP Version. This setting controls the format and the broadcasting method of the RIP
packets that the router sends. It recognizes both formats when receiving. By default,
the RIP function is disabled.
- RIP-1 is universally supported. It is adequate for most networks, unless you have
an unusual network setup.
- RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in
RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting.
Use Router as a DHCP Server. This check box is selected by default so that the router
functions as a Dynamic Host Configuration Protocol (DHCP) server.
- Starting IP Address. Specify the start of the range for the pool of IP addresses in
the same subnet as the router.
- Ending IP Address. Specify the end of the range for the pool of IP addresses in
the same subnet as the router.
Address Reservation. When you specify a reserved IP address for a computer on the
LAN, that computer receives the same IP address each time it accesses the router’s
DHCP server. Assign reserved IP addresses to servers that require permanent IP
settings.
Use the Router as a DHCP Server
By default, the router acts as a DHCP server. The router assigns IP, DNS server, and default
gateway addresses to all computers connected to the LAN. The assigned default gateway
address is the LAN address of the router. The router assigns IP addresses to the attached
computers from a pool of addresses specified in this screen. Each pool address is tested
before it is assigned to avoid duplicate addresses on the LAN. For most applications, the
default DHCP and TCP/IP settings of the router are satisfactory.
The router delivers the following parameters to any LAN device that requests DHCP:
An IP address from the range you have defined
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear JWNR2000v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear JWNR2000v3 in the language / languages: English as an attachment in your email.

The manual is 7,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info