710895

Netgear GS748TP Manual

125
Zoom out
Zoom in
Previous page
1/216
Next page
GS700TP Smart Switch Software Administration Manual
4-38 Configuring Switching Settings
v1.0, April 2008
–Backup – Provides a backup path to the designated port path toward the Spanning
Tree leaves. Backup ports occur only when two ports are connected in a loop by a
point-to-point link, or when a LAN has two or more connections connected to a shared
segment.
– Disabled – The port is not participating in the Spanning Tree.
• Mode – Displays the current STP mode. The STP mode is selected in the STP
Configuration screen. The possible field values are:
– STP – Classic STP is enabled on the device.
– RSTP – Rapid STP is enabled on the device.
• Fast Link Operational Status – Displays the Fast Link status for the interface. If Fast
Link is enabled for a port, the port is automatically placed in the forwarding state. The
possible field values are:
– Enabled – Fast Link is enabled on the interface.
– Disabled – Fast Link is disabled on the interface.
• Status – Displays the RSTP status for the interface. The possible field values are:
– Enabled – RSTP is enabled on the interface.
– Disable – RSTP is disabled on the interface. This is the default value.
• Point-to-Point Admin Status – Select whether a point-to-point link is established, or if
the device is permitted to establish a point-to-point link. The possible field values are:
– Enable – Enable a point-to-point link, or configure to automatically establish a point-
to-point link. To establish communications over a point-to-point link, the originating
PPP first sends Link Control Protocol (LCP) packets to configure and test the data
link. After a link is established and optional facilities are negotiated as needed by the
LCP, the originating PPP sends Network Control Protocol (NCP) packets to select and
configure one or more network layer protocols. When each of the chosen network
layer protocols has been configured, packets from each network layer protocol can be
sent over the link. The link remains configured for communications until explicit LCP
or NCP packets close the link, or until some external event occurs. This is the actual
switch port link type. It may differ from the administrative state.
– Disable – Disable point-to-point link.
–Auto – Enable the device to automatically establish a point-to-point link.
• Point-to-Point Operational Status – Displays the point-to-point operating state.
… 125 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear GS748TP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear GS748TP in the language / languages: English as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info