614018
13
Zoom out
Zoom in
Previous page
1/64
Next page
Troubleshooting | 13
6 720 815 281 (2014/10)MZ 100
5Troubleshooting
The indicator shows the operating condition of the module.
A number of faults are also shown in the display of the corresponding
user interface.
6 Environment / disposal
Environmental protection is a fundamental corporate strategy of the
Bosch Group.
The quality of our products, their efficiency and environmental safety
are all of equal importance to us and all environmental protection
legislation and regulations are strictly observed.
We use the best possible technology and materials for protecting the
environment taking into account of economic considerations.
Packaging
We participate in the recycling programmes of the countries in which our
products are sold to ensure optimum recycling.
All of our packaging materials are environmentally friendly and can be
recycled.
Old electrical and electronic appliances
Electrical or electronic devices that are no longer
serviceable must be collected separately and sent for
environmentally compatible recycling (in accordance
with the European Waste Electrical and Electronic
Equipment Directive).
To dispose of old electrical or electronic devices, you
should use the return and collection systems put in place
in the country concerned.
Use only original spare parts. Any damage resulting from
spare parts that are not supplied by the manufacturer is
excluded from liability.
If a fault cannot be rectified, please contact the
responsible service engineer.
Indicator Possible cause Remedy
permanently off
(at coding switch I)
Coding card on 0 Set the coding card.
Power supply
interrupted.
Switch on the power
supply.
Fuse is defective
When the power
supply is switched
off, replace the fuse
( Fig. 25, page 63).
Short circuit in the
BUS connection
Check BUS
connection and repair
if required.
permanently red
(at coding switch I)
Internal fault Replace module.
flashing red
(at coding switch I
or temperature
switch II)
Coding switch to
invalid position or in
intermediate position
Set the coding card.
flashing green
(at coding switch I)
Maximum cable length
for BUS connection
exceeded.
Make shorter BUS
connection.
Fault shown on
user interface display
The user interface
instructions and the
service manual
contain further
information on
troubleshooting.
I/O controller or room
thermostats installed
without BUS
connection and the
DHW temperature in
the cylinder is not
reached within 3
hours.
Operation alternates
between heating/
DHW
Check heat exchanger
for limescale
deposits, descale if
necessary.
No BUS participant;
no setpoint received.
Check BUS
connection and repair
if required.
Temperature sensor is
faulty.
Replace temperature
sensor.
permanently green
(at coding switch I)
No fault Standard operation.
Table 10 Troubleshooting
0
1
2
3
4
S
Y
I
off
40
50
60
70
max
IIII
6 720 804 106-23.1O
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nefit MZ 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nefit MZ 100 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info