614016
16
Zoom out
Zoom in
Previous page
1/108
Next page
6 720 813 621 (2014/12) MM100
16 | Installation
3.3.3 Overview of the terminal assignment
This overview shows which system parts can be connected.
The system components identified with an asterisk (*) are
possible alternatives. Depending on the use of the module
(encoding on the module and configuration with the remote
control), one of the components is connected to the terminal
(such as “PC1” or “PW1” to terminal “PC1”). Connect the
system parts according to the wiring diagram ( Tab “Wiring
diagrams with system schematics”).
Legend to the above figure and Fig. 19 to 27 from page 98:
Possible with a heat pump ( ) or not possible with
a heat pump ( )
Possible with other heat sources as heat pumps
( ) or not possible ( )
Earth lead
Temperature/temperature sensor
L Phase (mains voltage)
N Neutral conductor
Terminal designations:
230 V AC Mains voltage connection
BUS BUS system connection EMS 2
MC1 Temperature switch (monitor circuit)
MD1 Volt free contact for constant heating circuit:
external signal for heat requirement ()– heating
pump on/off ( additional accessories)
OC1 No function
PC1 Pump connection (pump circuit)
T0 Temperature sensor connection to low loss header
or a buffer cylinders (temperature sensor)
TC1 Connection for heating circuit flow temperature
sensor or cylinder temperature sensor
(temperature sensor circuit)
VC1 Mixing valve actuator connection (valve circuit):
Terminal 43: mixer open (for warmer heating; for
cooler cooling (cooling function)
Terminal 44: mixer closed (for cooler heating; for
warmer cooling (cooling function)
-or-
DHW circulation pump connection in DHW circuit
(coding card on 9 or 10):
Terminal 43: DHW circulation pump phase
Terminal 44: not assigned
The maximum power consumption of the
connected components and assemblies must not
exceed the output stated in the module
specification.
If the mains voltage is not supplied via the
heat source electronic system, install a
standard isolator (in accordance with
EN 60335-1) on site to disconnect all poles
from the power supply.
6 720 810 981-01.2O
BUS BUST0 TC1
M
PC1
PW1*
NL
MC1
M
VC1
N
M
N
4
43 44
PW2*
TW1*
MD1
%-rel
N7475
VC1
M
PW2*
NL
230 V AC 230 V AC
N L N N 43 N 6344 15 16L
120/230VAC 120/230VAC
MC1VC1 PC1
1212 12
TC1
T0 BUS
MM100
12
BUS
120/230 V AC
≤ 24V
≤ 24V
12 2
OC1
31
MD1
0
1
2
3
4
5
6
7
8
9
10
10
1)
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nefit MM100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nefit MM100 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info