539929
13
Zoom out
Zoom in
Previous page
1/84
Next page
English.3
English
Display Card Installation
1.
Following your PC manufacturer’s guidelines, open your computer to access the PCI, AGP or PCI E slot.
2. Place the display card into an available
PCI, AGP or PCI E
slot and secure all screws.
3. Replace the computer cover.
NOTE: For information on installing drivers, display modes in multimonitor mode, setting the dip switches,
please refer to the display card manufacturer’s documentation.
Connecting the LCD to Your PC
Once the display card is successfully installed, follow these instructions to connect the display to your PC.
1. Shut down your computer and turn off the power.
2. Connect the DVI-D signal cable to the connector of the display card in your system (Figure A.1).
Tighten all screws.
NOTE: For dual displays, plug a DVI-D cables into Port 1 and Port 2 of the display card
(Figure A.1).
For further information on display card installation, refer to the display card manual.
3. Rotate the screen to portrait mode. Refer to “Screen Rotation” section in this manual.
4. Remove the connector cover by pressing this mark (III) to unlock. Slide the cover to remove
(Figure B.1).
5. Connect the DVI-D signal cable to the connector on the back of the display (Figure C.1).
NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD
module, and/or shorten the module life.
6. Connect one end of the power cord to the AC inlet on the back of the display and the other end to the power outlet
(Figure C.1). Replace the connector cover.
NOTE: Please refer to the “Power Cord Important Information” section of this manual for proper selection of AC
power cord.
7. Place the DVI cable and the power cable into the specific hooks as indicated (Figure D.1).
NOTE: Make sure all cables are resting flat against the stand.
Please check Raise and Lower, Screen Rotation, and Tilt and Swivel functions (page 5) when you manage
cables.
Quick Start
Figure A.1
Port 2 for Dual Display
Figure C.1 Figure D.1Figure B.1
01_MD205MG-1_INSTALL_EN.P65 7/5/08, 10:09 AM3
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec MD205MG-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec MD205MG-1 in the language / languages: English, German, French as an attachment in your email.

The manual is 13,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info