512551
13
Zoom out
Zoom in
Previous page
1/17
Next page
13
WIND 3150 Installation and Operation Manual
NAVMAN
box needs to be. Allow extra length for
terminating the cable in the junction box. Cut
the masthead cable to this length from the
mounting block. Do not throw away the other
piece of cable.
5 Lead the bare end of the masthead cable into
the hole at the top of the mast, down the
conduit in the mast and out the hole at the
bottom of the mast. Fit a strain relief clamp or
cable tie to the cable at the mast top. Fill both
cable holes in the mast with sealant.
6 Feed the end of the cable through a gland on
the cable junction box. Strip the cable jacket off
and terminate the wires on the terminal block
supplied.
7 Take the piece of masthead unit cable that you
cut off earlier and connect the cable into the
back of the WIND 3150 display unit. Run the
cable between the display unit and the cable
junction box:
Keep the cable away from other cables,
engines, fluorescent lights and power
inverters.
Secure the cable at regular intervals.
8 Cut the cable to length, allowing extra length
for terminating the cable in the joining box.
Feed the end of the cable through the other
gland on the cable junction box. Strip the cable
jacket off and terminate wires on the terminal
block, matching the wire colours.
9 Screw the lid on the junction box and screw the
box in place on a panel.
10 Fit the wind cups to the shaft on the masthead
unit using the allen key supplied.
11 Attach the arm to the mounting block:
Plug the arm into the mounting block.
Screw the sleeve on the arm onto the
mounting block.
Power/data wiring
1 Wire the display unit power/data cable:
The unit requires 12 V DC power. Fit a
power switch and fuse to the power supply
or power the unit from a fused auxiliary
switch. The fuse should be 1 A for up to five
instruments.
The output to external beepers and lights is
switched to power negative by the WIND
3150 to sound the alarm. If the external
beepers and lights require more than
250 mA DC total, fit a relay.
A single unit can be wired as shown below:
Fit mounting
block to mast
top (Step 1)
Fit
wind
cups
Mast
Plug arm
into block
Arm
Screw sleeve
onto block
Mast
WIND 3150
Display unit
Cable junction box
Cable
Hole in mast,
fill with sealant
Forward
Hole in mast,
fill with sealant
Cable runs
down inside of
mast in conduit
Cable strain relief
Installed Masthead Unit
Green
Switch
Yellow
White
Orange
Blue
Black
Red
Fuse
1 A
Mast head unit cable
External beepers
or lights (optional)
NMEA in (optional)
12 V
DC
power
NMEA out (optional)
NavBus (optional)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Wind 3150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Wind 3150 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Wind 3150

Navman Wind 3150 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info