512551
12
Zoom out
Zoom in
Previous page
1/17
Next page
12
NAVMAN
WIND 3150 Installation and Operation Manual
Correct installation is critical to the performance of
the unit. It is vital to read this section of the manual
and the documentation that comes with the other
parts before starting installation.
The WIND 3150 can:
Drive external beepers or lights for the alarm.
Send and receive data from other NAVMAN
instruments connected via NavBus. Settings
for alarms, units, calibration and backlighting
are shared (see section 9-1).
Send and receive NMEA data to and from other
instruments (see section 9-2).
Warnings
The unit is waterproof from the front. Protect the rear
of the unit from water, or else water might enter the
breathing hole and damage the unit. The warranty
does not cover damage caused by moisture or water
entering the back of the unit.
The cable up the mast to the masthead unit must
run in conduit.
11-1 Installation
WIND 3150 display unit
1 Choose a location for the display unit that is:
Easily seen and protected from damage.
At least 100 mm (4") from a compass and
at least 500 mm (20") from a radio or radar
antenna.
Away from engines, fluorescent lights, and
power inverters.
Accessible from behind; the minimum
clearance required at the back is 50 mm
(2") (see mounting diagram).
With the back of the unit protected from
moisture.
2 The unit must mount on a flat panel which is
less than 20 mm (0.75") thick. Stick the
mounting template in place. Drill a 50 mm (2")
fixing hole through the centre hole in the
template. Note that the template allows space
around the unit for the protective cover.
3 Remove the fixing nut from the back of the unit.
Insert the back of the unit through the mounting
hole. Hand tighten the fixing nut.
11 Installation and setup
Masthead unit
Plan the installation. Read through these instructions
before you install the masthead unit and plan where
you will fit the mounting block and where you will drill
the cable holes in the mast. It is usually easiest to
install the masthead unit when the rig is off the boat.
1 The mounting block is at one end of the 30 m
(98 ft) masthead cable. Fit the mounting block
on top of the mast:
With the base of the block horizontal.
With the fitting for the masthead arm facing
forward, parallel to the centre line to within
a few degrees (if the arm does not face
exactly forward, the wind angle must be
calibrated, see section 8-1).
20 mm (0.75") maximum
panel thickness
Fixing nut
Display unit
Fixing hole
50 mm (2")
Side view of display unit mounting:
Ensure that any holes that you cut will not
weaken the boat or the mast. If in doubt, consult
a qualified boat builder or marine engineer.
Use the self-tapping screws provided.
2 Drill an 8 mm (5/16") hole at the top of the
mast close to the mounting block for the cable
to enter the mast. Do not install the masthead
cable yet.
3 Drill an 8 mm (5/16") hole at the bottom of the
mast at a convenient place for the cable to exit
the mast. You will fit the cable junction box
close to this hole; it should be in a dry place
and not in the bilge.
4 Calculate how long the cable from the
masthead mounting block to the cable junction
Cables Clearance
50 mm (2") minimum
forward
Arm faces forward
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Wind 3150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Wind 3150 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Wind 3150

Navman Wind 3150 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info