663850
8
Zoom out
Zoom in
Previous page
1/34
Next page
G-PILOT 3100 Installation Manual
NAVMAN
8
The recommended installation sequence is:
1 Read this manual and the documentation
that comes with the other parts.
2 Plan the installation: select where the
equipment and wiring will be installed
(see section 3-2).
3 Install the main unit (see section 3-3).
4 Install the steering drive and wire the heavy
duty and light duty power supplies (see
section 3-4).
5 Install the rudder feedback unit (see
section 3-5).
6 Install the compass (see section 3-6).
3 Installation
3-1 Installation sequence
Warning Correct installation is critical to the
performance of the unit. It is vital to read this
manual and the documentation that comes with
the other parts before starting installation.
Warning
The G-PILOT main unit is not waterproof.
Mount the unit in a dry place.
The G-PILOT display unit is waterproof
from the front. Protect the rear of the unit
from water, or else water might enter the
breathing hole and damage the unit. The
warranty does not cover damage caused
by moisture or water entering the back of
the unit.
The compass, gyro and rudder feedback
unit are completely waterproof.
Warning Ensure that any holes that you cut
will not weaken the boat’s structure. If in doubt,
consult a quali ed boat builder.
7 Install the gyro (see section 3-7).
8 Install the display unit and any other
marine instruments that will be used with
the G-PILOT 3100 (see section 3-8).
9 Carry out the dockside setup (see
section 4).
10 Carry out the sea trials (see section 5).
If you are unsure where a part should be
installed, mount and wire the part temporarily,
without cutting holes in the boat. After the sea
trials have been completed, install and wire
the part permanently.
2-2 Other parts required
Power supply: The G-PILOT 3100 requires
two power supplies, both nominally 12 V DC:
A heavy duty supply for the steering drive
A light duty supply for the G-PILOT 3100
electronics and display unit; this supply
also powers any additional display units
and other instruments.
The power supplies require one or two
switches and fuses or circuit breakers (see
section 3-4).
Steering drive: The G-PILOT 3100 can power
a hydraulic pump, constantly running pump set,
hydraulic linear drive or mechanical drive rated
at 12 V DC and up to 20 A.
Rudder linkage: To link rudder to rudder
feedback unit (see section 3-5).
For wiring, see Select Wire Table in section
3-4-2.
External beepers or lights (optional ): The
external output is switched to ground, 30 V DC
and 250 mA maximum. If the beepers and lights
require more than 250 mA total, t a relay.
Other marine instruments (optional): Wind,
speed or GPS instruments can be connected
(see section 1-2).
Other parts: For systems of several
instruments, wiring and connectors are
required. Navman junction boxes can simplify
wiring several Navman instruments together
(see section 1-2 or the NavBus Installation
and Operation Manual).
Coupling connectors and 10 m (33 ft)
extension cables are available to extend the
rudder feedback unit, compass or gyro cables.
Do not t more than one extension cable to
each unit.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman G-PILOT 3100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman G-PILOT 3100 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman G-PILOT 3100

Navman G-PILOT 3100 User Manual - English - 36 pages

Navman G-PILOT 3100 User Manual - German - 33 pages

Navman G-PILOT 3100 Installation Guide - German - 32 pages

Navman G-PILOT 3100 User Manual - Dutch - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info