470011
25
Zoom out
Zoom in
Previous page
1/30
Next page
26
Fish 4430/4431 Installation and Operation Manual
Warning
1 Amp fuses must be positioned where shown
in the wiring diagrams.
If possible, route the transducer cables away
from other wiring on the boat. Electrical noise
from engine wiring, bilge pumps and other
electrical equipment can affect the unit.
The shortest and most direct connection to the
boat’s battery helps to minimise voltage drop.
Ensure that any cable connections do not lay
in the bilge.
Two wiring options are described in this
section:
· Basic Wiring. This does not start the
fishfinder automatically when the boat
ignition is switched on and it disables the
engine hours counter.
· Auto Power Wiring. This must be used for
engine hours and fuel computer options.
Important
The FISH 4430/4431 must be run off a 12
volt battery and must not be run off a circuit
without a battery.
Basic Wiring
5-4 Wiring Connection
1A fuse
1A fuse
1A Fuse
Red
Yellow
Black
Main
switch
12 V DC
Black wire: Connect this to the negative
battery terminal.
Red wire: Connect this to the 12 V positive
battery terminal after the main switch. Fit a 1
Amp fuse as shown.
Yellow wire: Connect this to the black wire.
This disables the engine hours counter.
Power on the fishfinder manually whenever the
main switch is on.
White
(NMEA out)
Green
External
Beeper or
Light
Red
Yellow
Black
Main
switch
12 V DC
Ignition
switch
To ignition
system
Auto Power Wiring
Black wire: Connect this to the negative
battery terminal.
Red wire: Connect this to the 12 V positive
battery terminal after the main switch. Fit a 1
Amp fuse as shown.
Yellow wire: To enable the engine hours
counter and start the fishfinder automatically
when the ignition is turned on, connect the
yellow wire to the ignition system, through a 1
Amp fuse.
Note: That the fishfinder cannot be turned off
while the ignition is on.
Flashing Light and/or External beeper
(F4431 ONLY)
Use the green wire, if desired, to connect a
secondary alarm indicator such as a flashing
light or a 12 V external beeper with a built in
drive circuit. Refer to the wiring diagram. If the
external beeper or light requires more than
250 mA DC total, fit a 12 V relay. Consult your
NAVMAN dealer for more advice.
NMEA Instruments (F4431 ONLY)
Use the white wire, if desired, to connect the
fishfinder to other NMEA instruments such as
NAVMAN’s depth repeater. (See section 5-5 for
more information).
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman FISH 4431 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4431 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman FISH 4431

Navman FISH 4431 Usermanual and installation guide - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info