470011
6
Zoom out
Zoom in
Previous page
1/30
Next page
7
Fish 4430/4431 Installation and Operation Manual
2 Getting started
For deep-sea fishing with the FISH 4430/4431,
a rapid change in temperature may indicate
the edge of a warm or cold current. The
temperature difference can form a barrier, and
the fish may not swim through this. Search for
fish on either side of the barrier.
Cleaning and maintenance
The FISH 4430/4431 should be cleaned
with a damp cloth or mild detergent. Avoid
abrasive cleaners and petrol or other solvents.
Always cover or remove a transom-mounted
transducer when repainting the hull. If painting
over a through hull transducer with antifouling
paint then use only one coat of paint. When
repainting the transducer, remove previous
coats of antifouling paint by sanding it lightly.
When not in use, the FISH 4430/4431 can either
be removed from the installation bracket and
stored in a safe, dry, cool place such as the
NAVMAN carry bag, or left on the installation
bracket and securely covered with the optional
sun cover.
Power and transducer connection
FISH 4430
One end of the integrated transducer/power
cable has an 8 pin LT connector plug. Push this
plug into the socket located on the rear of the
display unit, then turn the collar to lock. Make
sure that the collar is secure for a watertight
connection.
FISH 4431
One end of the power cable has a black 8 pin LT
connector plug. Push this plug into the lower
socket, which has a black nut and is located on
the rear of the display unit, then turn the collar
to lock. Make sure that the collar is secure for a
watertight connection.
One end of the transducer cable has a blue
8 pin LT connector plug. Push this plug into
the upper socket, which has a blue nut and is
located on the rear of the display unit, then
turn the collar to lock. Make sure that the collar
is secure for a watertight connection.
If the transducer is not connected, the
message “NO TRANSDUCER DETECTED. ENTER
SIMULATION MODE?” will appear. Press
to switch between YES, NEVER or NO. (More
information on the simulation mode can be
found in the following section). Press to
confirm the selection and the startup sequence
will continue.
(Note: If the transducer was not intentionally dis-
connected, turn the display unit off and refer to the
section on Troubleshooting in Appendix B.)
Names of keys:
Cursor key
key
+ gain key
- gain key
Power key
Definition of Press and Hold in this manual:
· Press means to push the key for less than
one second.
· Hold means to push and hold the key down
for more than one second.
Power on
To turn the fishfinder on press .
Note: if the unit is wired for Auto Power (see sec-
tion 5-4) the fishfinder will turn on automatically
when the boat’s ignition is turned on.
A title screen briefly appears which displays
basic product information, including the
software version.
The FISH 4430/4431 then automatically displays
the screen that was last used.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman FISH 4431 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4431 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman FISH 4431

Navman FISH 4431 Usermanual and installation guide - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info