Manual Navman FISH 4200 (page 8 of 32) (English)

470014

Zoom out

Zoom in

1/32

NAVMAN

FISH 4200 Installation and Operation Manual

Alarms can be enabled to automatically detect certain

conditions, such as the water being too shallow. The

trigger settings for the alarms can be defined to suit

the boat and individual preferences.

The FISH 4200 has seven alarms, TOO SHALLOW,

TOO DEEP, FISH ALARM, TEMP VALUE, TEMP

RATE, LOW BATTERY and LOW FUEL.

The alarm symbols and beeper cycles for all of the

alarms are shown in section 4-1. The FISH ALARM

is three short beeps, the TOO SHALLOW ALARM is

a rapid continuous beep while all others are a slower

continuous beep.

When an alarm condition is met, then:

· the beeper sounds.

· the ALARMS menu is displayed on the

screen with the activated alarm(s) flashing.

Press any key to acknowledge the alarm, stop the

beeping and remove the ALARMS menu. This does

Select MAIN MENU - HISTORY to display the

HISTORY screen.

The HISTORY screen displays the most recent

echoes on the right of the screen and the oldest

echoes on the left. These eventually disappear off

the screen.

The vertical bar on the right edge of the screen is the

zoom bar. This shows the zoom range. To adjust the

zoom range see section 3-4.

3-1 ALARMS

not disable the alarm. The symbol will continue to

flash until the alarm condition is no longer present.

Alarms automatically re-enable

The TOO SHALLOW, TOO DEEP, LOW FUEL and

LOW BATTERY alarms automatically re-enable

when the value moves outside the alarm trigger

setting.

The TEMP VALUE alarm automatically re-enables

when the temperature is more than 0.45°F (0.25°C)

above or below the alarm trigger setting.

The TEMP RATE alarm automatically re-enables

when the rate of temperature change falls below the

trigger setting by more than 0.2°F (0.1°C) per minute.

Enabling Alarms and Changing Trigger

Values

See section 4-1 for information about enabling alarms

and changing the trigger values.

3-2 HISTORY screen operation

the boat. This means that the HISTORY screen

display moves across the screen more quickly than

when the boat is travelling in deep water. In deep

water, the echoes take longer to travel between the

objects and the boat, producing a display that moves

across the screen more slowly.

Note 1: Different fish symbols can be selected (see

section 4-4).

Note 2: The depth of bottom can be adjusted for keel

offset (see section 4-8).

Range

Range is the depth of water displayed vertically. The

NAVMAN fishfinder has two range modes, Auto

Range and Manual Range:

· In Auto Range, the fishfinder adjusts the depth

range automatically so that the bottom is always

shown in the lower part of the screen. The use

of Auto Range is recommended.

· In Manual Range, the fishfinder shows only a

selected depth range. In areas of rapidly

changing bottom depth, such as the sea floor

around pinnacles, it can be useful to prevent

the screen from rescaling to always show the

bottom. If the bottom is deeper than the

specified depth range, it will not be shown on

the display screen.

To change the range mode, see section 3-9.

The HISTORY screen does not show a fixed distance

travelled by the boat; rather, it displays what has

passed below the boat during a certain period of time.

The actual display depends upon the boat speed and

the depth of the water.

As the boat travels through shallow water, the echoes

have less distance to travel between the objects and

Fish symbol

with depth

Selected depth range (0 to 150')

Alarms

Bottom

Zoom bar

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4200 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Navman FISH 4200 Manual

Product: