470014
6
Zoom out
Zoom in
Previous page
1/32
Next page
6
NAVMAN
FISH 4200 Installation and Operation Manual
Power and transducer connection
The FISH 4200 has two sockets located on the rear of
the unit. The power cable has a black 8 pin LT
connector plug. Push this plug into the lower socket,
which has a black nut and is located on the rear of the
display unit, then turn the collar to lock. Make sure
that the collar is secure for a watertight connection.
The transducer cable has a blue 8 pin LT connector
plug. Push this plug into the upper socket, which has
a blue nut and is located on the rear of the display
unit, then turn the collar to lock. Make sure that the
collar is secure for a watertight connection.
If the transducer is not connected, the message “NO
TRANSDUCER DETECTED. ENTER SIMULATION
MODE?” will appear. Press
to switch between YES
or NO. (More information on the simulation mode can
be found in the following section). Press
to
confirm the selection and the startup sequence will
continue. (Note: If the transducer was not intentionally
disconnected, turn the display unit off and refer to the
section on Troubleshooting in Appendix B.)
Names of keys:
Cursor key
key
+
gain key
-
gain key
Power key
Definition of Press and Hold in this manual:
· Press means to push the key for less than one
second.
· Hold means to push and hold the key down for
more than one second.
Power on
To turn the fishfinder on press .
Note: if the unit is wired for Auto Power (see section
5-4) the fishfinder will turn on automatically when
the boat's ignition is turned on.
A title screen briefly appears which displays basic
product information, including the software version.
The FISH 4200 then automatically displays the
screen that was last used.
Power off
To turn the fishfinder off, hold . A countdown box
appears. Continue to hold
for three seconds until
the fishfinder turns off.
Note: if the unit is wired for Auto Power (see
section 5-4) the fishfinder can only be turned off
when the boat’s ignition is turned off.
Language selection
To check which language is currently selected,
press
to display the MAIN MENU.
Follow these steps to change the language:
1. Power off the unit.
2. While the unit is off, hold down the
key.
3. Keep holding down the key and power
on the unit.
4. The screen displays a list of languages.
Press the Cursor or key to highlight a
language, then press the Cursor key to
select it. The fishfinder will continue the
startup sequence.
For further information, see section 4-8.
Backlighting
Use the button to adjust the backlighting to suit
individual preferences.
Press
once, at any time, to see the backlight
bar. This is displayed at the bottom of the screen
and shows the current setting.
Press
repeatedly until the desired backlighting
level is achieved. The backlight bar will disappear
2 seconds after the last press.
Fuel Computer
With an optional fuel kit the FISH 4200 becomes a
sophisticated yet easy to use fuel computer.
2 Getting started
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman FISH 4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman FISH 4200 in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info