707126

Native Traktor Pro 3 Manual

121
Zoom out
Zoom in
Previous page
1/212
Next page
For more information about the Mix Recorder Preferences, refer to Preferences – Mix Recorder
Page.
Configuring TRAKTOR for Broadcasting
To broadcast your mix you need to adjust TRAKTOR to send your
Before getting started, it is necessary to configure TRAKTOR so that the local client can connect
to the server and the metadata of the radio stream contains the correct information:
1. Open Broadcasting Page in the Preferences.
2. Adjust the Proxy Settings according to your current Internet configuration. If you are not us-
ing a proxy, simply check None.
3. Under Server Settings, input the Address of the Icecast server you want to connect to. This
can be either a hostname or an IP-address.
4. Specify the port where the Icecast server can be reached. Most servers use the default set-
ting of 8000.
5. Type in the Mount path and Password. This information can be obtained from the host of
the Icecast server and permits only authorized clients to stream data from there.
6. Select the Format for the streaming. Note that with a higher bit rate, more bandwidth is used
for every single stream. Therefore, given the same bandwidth, fewer listeners can tune in at
the same time.
7. In the Metadata Settings, enter the information about your broadcast. This information is
sent to the server and your listeners.
TRAKTOR is ready for broadcasting.
For more information about the Broadcasting page in the Preferences, refer to Preferences –
Broadcasting Page.
Adjusting Recording level
1. Click the Audio Recorder button in the Global Section to display the AUDIO RECORDER.
2. Playback a track on any Deck to monitor the incoming audio signal in the AUDIO RECORD-
ER.
The Recordings Level Meter in the AUDIO RECORDER reflects the incoming audio signal. If
not, make sure the channel fader is raised and the crossfader is positioned accordingly.
3. Adjust the recording level with the Record GAIN knob.
For more information about adjusting levels, refer to Adjusting Gain Levels for Incoming Audio Sig-
nals.
Starting Broadcast
1. Click the Broadcast button to start broadcasting.
If the button is highlighted, you are connected to the icecast server. If the Broadcast button is
flashing, the connection with the Icecast server could not be established. In this case, check
if the settings on the Broadcasting Page in the Preferences are entered correctly.
2. To stop broadcasting, click the Broadcast button again.
Advanced Operation of TRAKTOR
113
… 121 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Native Traktor Pro 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Native Traktor Pro 3 in the language / languages: English as an attachment in your email.

The manual is 9,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info