707122
17
Zoom out
Zoom in
Previous page
1/30
Next page
(10) SHAPE Modulation Source: Select the modulation source for the Shape Modulation Amount
Controls (9). Modulation sources include MOD 1, MOD 2, F. ENV (Filter Envelope).
(11) Semi: Adjusts the pitch of Oscillator 1 in a range of -48 to +48 semitones.
(12) Fine: Adjusts the pitch of Oscillator 1 in the range of -50 to +50 cents.
(13) Sub/Noise Switch: Select between sub-oscillator or white noise for Oscillator 1.
(14) Mix: Adjusts the volume balance between Oscillator 1 and Oscillator 2. In the far left position,
only Oscillator 1 can be heard, in the far right position, only Oscillator 2 can be heard. When Mix is
centered there is a perfect balance between both oscillators.
(15) Sync: Forces Oscillator 2 to be hard synced to Oscillator 1. Try increasing the pitch of Oscilla-
tor 2 when hard sync is engaged, for a classic sync effect.
(16) FM (Frequency Modulation): Modulates the frequency of Oscillator 1 using the output of Oscil-
lator 2 as a modulation source. FM produces more harmonically rich waveforms. Experiment with
the pitch of the Oscillators to create non-tonal, metallic sounds and bell-like sounds.
(17) Semi: Adjusts the pitch of Oscillator 2 in a range of -48 to +48 semitones.
(18) Fine: Adjusts the pitch of Oscillator 2 in the range of -50 to +50 cents.
(19) Sub/White Noise Switch: Select between sub-oscillator or white noise for Oscillator 2.
(20) Keytracking On/Off: Turns keytracking on and off for Oscillator 2. When turned off, a fre-
quency value can be set in hertz.
(21) Sine Level: Adjusts the level of the sine waveform for Oscillator 2.
(22) Sawtooth Level: Adjusts the level of the sawtooth waveform for Oscillator 2.
(23) Pulse Level: Adjusts the level of the pulse waveform for Oscillator 2.
(24) Sub/Noise Level: Adjusts the level of the sub-oscillator or white noise for Oscillator 2, de-
pending on which one is selected using the Sub/Noise Switch (19).
(25) Sine Shape: Adds a second Sine wave at an octave higher than the fundamental frequency.
Turn the knob to the right to add this extra Sine.
(26) Saw Shape: Morphs the waveform from a triangle (left) to a sawtooth (middle), to a PWM
sawtooth (right). Double click to set to a pure sawtooth wave.
(27) Pulse Shape: Controls the pulse width of the pulse waveform. Double click to set to a pure
square wave.
(28) Sub Shape: Controls the pulse width of the Sub waveform. Double click to set to a pure
square wave.
(29) Shape Modulation Source: Select the modulation source for the Shape Modulation Amount
controls (30). Modulation sources include MOD 1, MOD 2 F. ENV (Filter Envelope).
(30) Shape Modulation Amount: Applies modulation from the selected Shape Modulation Source
(29) to the waveform above.
5.3. Filter
The Filter takes the basic, raw sound of the oscillators and noise generator and subtracts frequen-
cies, changing the tone of the sound. This change can be varied over time using the Filter Enve-
lope or modulated using the modulators (MOD 1 & 2) to produce more dynamic animated timbres.
Overview of SUPER 8
15
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Native Super 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Native Super 8 in the language / languages: English as an attachment in your email.

The manual is 5,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info