707496
6
Zoom out
Zoom in
Previous page
1/29
Next page
4
Installation - Getting Started
2 Getting Started
UnitiServe-SSD should be installed horizontally on a dedicated equipment stand intended
for the purpose. Do not stand UnitiServe-SSD directly on top of another item of equipment.
UnitiServe-SSD should be installed in its final location before connecting cables or
switching on.
UnitiServe-SSD can be connected to a computer network to retrieve album data and
artwork from the internet, to stream music around the home using NaimNet hardware, or
to take advantage of one of its alternative user interfaces. If UnitiServe-SSD is to be used
in a network it is important that the network is working when UnitiServe-SSD is connected
and switched on.
Locally connected audio amplifiers should not be switched on before UnitiServe-SSD is
switched on. The UnitiServe-SSD power switch is located on the rear panel.
To begin installation first identify the rear panel network, audio output and power input
sockets, and connect the appropriate cables.
2.1 Internet/Network Connections
While UnitiServe-SSD can be used in “stand-alone” mode
without any network connection, if its full capabilities are
to be realised it requires connection to an “always on”
internet service via an ethernet router/modem with a built-
in firewall.
If UnitiServe-SSD is to be used in a NaimNet/StreamNet
network audio system, the network connection also
enables UnitiServe-SSD to communicate with other
network devices and provides access to its alternative user
interfaces.
UnitiServe-SSD is set up when originally shipped not to
require any further network configuration but to connect
to a network automatically (it uses DHCP by default).
However, if your UnitiServe-SSD has been previously used,
its network configuration may have been altered leaving
it unable to connect automatically. Contact your retailer,
installer or Naim Audio directly if this appears to be the
case.
Note: A UnitiServe-SSD used in stand-alone mode and
switched on without a working network connection will
revert to an internal IP address only suitable for stand-alone
use. To restore the default DHCP setup, switch UnitiServe-
SSD off, connect the network and switch it on again.
2.1.1 Network Hardware
Conventional ethernet network connection is strongly
recommended for the most consistent and secure
UnitiServe-SSD operation.
Ethernet-over-mains hardware may be used and provides
a simple and convenient method of home network
connection. However, depending on mains wiring factors
specific to each home environment, the presence of
network data on the mains supply may compromise
overall system sound quality. If any sound quality
compromise is found to be unacceptable, dedicated
network cabling should be installed.
2.2 Power Supply Connection
UnitiServe-SSD is powered by an external power supply.
Connect the output cable of the power supply to the
UnitiServe-SSD power input socket and the mains input
cable of the power supply to a mains outlet socket. Use
only the mains cable supplied.
2.3 Audio Connection
Connect one of the UnitiServe-SSD digital audio output
sockets (BNC coaxial or TosLink optical), to an appropriate
audio system digital input. For best performance use a
Naim DC1 digital coaxial interconnect cable.
2.4 Switch On
If UnitiServe-SSD’s network facilities are to be used ensure
that it is connected to a working internet connection
before switching it on and that all the necessary peripheral
equipment is appropriately connected and configured.
Switch on UnitiServe-SSD using the rear panel power switch.
Note: If UnitiServe-SSD is to be switched on from shutdown
mode, the power switch must be switched off and on again.
See Section 2.8 for more on shutdown mode.
After approximately one minute, during which the front
panel logo will flash, the user interface Home menu will
appear on the interface display. Navigation around the
interface will depend on the interface hardware chosen.
If using a touch screen, touch the interface graphics to
select items. If using the web browser or external display
interface, select options using a keyboard/mouse or, if a
remote handset is employed, its navigation (3456), ok,
home and back keys.
Note: Ensure that the unit
has adequate ventilation.
The ambient temperature
in the vicinity of the unit
should not exceed 35°C.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim UnitiServe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim UnitiServe in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim UnitiServe

Naim UnitiServe User Manual - English - 31 pages

Naim UnitiServe User Manual - German - 29 pages

Naim UnitiServe User Manual - German - 31 pages

Naim UnitiServe User Manual - French - 32 pages

Naim UnitiServe User Manual - Italian - 29 pages

Naim UnitiServe User Manual - Italian - 31 pages

Naim UnitiServe User Manual - Spanish - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info