707498

Naim NAT05 XS Manual

5
Zoom out
Zoom in
Previous page
1/34
Next page
E3
NAT05 XS Installation
4 NAT05 XS Installation
The NAT05 XS should be installed on a dedicated equipment stand intended for the
purpose. Do not stand it directly on top of another item of equipment. It should be
installed in its final location before connecting cables or switching on. Ensure also that the
system volume is turned down before switching on.
A number of power supply upgrade options are possible for the NAT05 XS. A diagram
illustrating the connection of one of these is shown in Section 7. Contact your local retailer
or distributor for advice if necessary on power supply connection.
4.1 Aerial Requirements
The NAT05 XS aerial input socket must be connected via
75Ω low-loss coaxial cable to a suitable aerial.
Ideally the aerial should be mounted on the roof, clear
of obstructions and as high as possible. Use of an aerial
preamplifier may disturb the muting operation of the tuner
and may cause cross-modulation problems (interference
from an adjacent strong radio broadcast). Such
preamplifiers should only be used as a last resort.
Radio broadcasts are usually transmitted from different
sites even though the target areas of the services may be
similar. This means that unless the transmitters are in almost
the same direction looking from your house, an aerial
aligned on one transmitter will give less than optimum
performance on the other. In these circumstances you
should fit an aerial rotator, or a less directional aerial if
appropriate. The more sensitive and directional the aerial
you use, the worse will be the reception in directions other
than the one towards which the aerial is pointing. If you
are particularly interested in receiving a wide range of VHF
transmissions an aerial rotator is a necessity. Your retailer
will be familiar with local conditions and will be able to
advise you on which stations you can expect to receive
satisfactorily.
4.2 Audio Outputs
The NAT05 XS is fitted with both DIN and RCA-phono output
sockets. Use of the DIN option is preferred, however, if the
RCA-phono option is to be used it must be selected once
the NAT05 XS is switched on. Section 5.2 describes output
socket selection.
4.3 Power Supply Upgrades
The NAT05 XS can be upgraded through the addition of
an external FlatCap or Hi-Cap power supply. The external
supply works with the internal power supply of the NAT05 XS
to offer both a greater number of separate supplies and
more sophisticated voltage regulation.
The upgrade power supply is connected to the NAT05 XS
via a 240° five-pin DIN cable. Ensure that both the power
supply and NAT05 XS are switched off when making
connections. Remove the link plug and connect the supply
cable ensuring that the connectors are securely attached.
From their respective power switches, switch on the power
supply followed by the NAT05 XS. Diagram 7.2 illustrates the
connection of an external power supply.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAT05 XS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAT05 XS in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info