707509
20
Zoom out
Zoom in
Previous page
1/44
Next page
E18
SUPERNAIT Integrated Amplifier
19.3 Digital Input Assignment
The default digital input socket assignment illustrated in
Table 19.2 may be changed if desired. Each selection
button may be assigned to any one of the four rear panel
digital input sockets.
Input assignment setup is accessed through the Supernait
program mode. To switch into (or exit from) program mode
press and hold the prog key on the remote handset (in
preamplifier mode). Program mode is indicated by a
flashing indicator on the front panel volume control.
Note: If no function is operated within five minutes of
entering program mode the Supernait will return to normal
mode automatically.
Once in program mode, to assign a digital input socket,
first press the required input selection button. Then, press
one of the record selection buttons to assign the desired
digital input. The record selection buttons assign digital
inputs as set out in the following table:
Record Select Button Digital Input Selection
cd (assigns) digital 1 (coaxial)
tuner (assigns) digital 2 (optical)
tape (assigns) digital 3 (coaxial)
av (assigns) digital 4 (optical)
As an example, to assign the tuner input selection button
to digital input 4 proceed as follows.
i) Enter program mode.
ii) Press the tuner input selection button.
iii) Press the av record selection button (which will
illuminate).
iv) Exit program mode.
To return an input selection button to its default analogue
input, repeat the assignment procedure.
For example, to return the tuner input selection button to its
analogue input socket.
i) Enter program mode.
ii) Press the tuner input selection button.
iii) Press the av (illuminated) record selection button (which
will extinguish).
iv) Exit program mode.
19.4 Record Outputs
The selection buttons arranged along the lower bank
select the source signal to be routed to the Supernait’s
record outputs.
These separate source and record sections enable one
source (a CD player, for example) to be listened to whilst
the output from another (say, the tuner) is simultaneously
selected for recording.
Note: Simultaneous and independent listen and record is
not possible with two digital sources.
19.5 Speaker Outputs
A stereo set of speaker connection sockets is provided
on the rear panel. Custom Naim Audio loudspeaker
connectors are supplied to make the connection and in
order to comply with current European safety regulations
these should always be used. Naim Audio speaker cable
will provide the best results; however, a wide range of
speaker cable types can be used without risk of damage
to the amplifier.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
19.6 Headphone Output
A 3.5mm headphone socket is provided on the front
panel. Insertion of a headphone plug will automatically
switch on the headphone amplifier and mute the speaker
outputs unless the Supernait is set up not to mute.
To prevent (or re-enable) automatic speaker muting,
enter program mode and press the record aux2 selection
button.
19.7 Auxiliary Inputs and Outputs
A bi-amp out (preamplifier output) DIN socket is provided
on the rear panel to enable an external upgrade power
amplifier or second (bi-amp) power amplifier to be used.
Note: Bi-amp out is the preferred socket for all external
power amplifier connections.
Also provided are separate pre-amp out and power-amp
in sockets. In normal use these sockets are connected by
an external link plug. The link plug should be removed only
if a power supply upgrade is to be used or an alternative
preamplifier is to use the Supernait power amplifier section.
Diagrams 20.3 to 20.5 illustrate use of these sockets.
When an external preamplifier is connected to the
Supernait power-amp in socket, a fault will initially be
indicated by the source mute button flashing. To clear the
fault, press and hold the flashing source mute button. This
will un-mute the power amplifier and turn off the display
and volume and balance indicators.
The Supernait provides an unfiltered analogue stereo
subwoofer output via a pair of RCA Phono sockets.
Note: The subwoofer output is a duplicate of the
preamplifier output. No low-pass filtering is applied.
19.8 Power Supply Upgrades
The Supernait preamplifier section can be upgraded
through the connection of an external Flatcap, Hi-Cap or
Supercap power supply. Diagrams illustrating power supply
upgrades are shown in the following section. The Supernait
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAP 300 DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAP 300 DR in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAP 300 DR

Naim NAP 300 DR User Manual - English - 16 pages

Naim NAP 300 DR User Manual - German - 44 pages

Naim NAP 300 DR User Manual - French - 44 pages

Naim NAP 300 DR User Manual - Italian - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info