707500
10
Zoom out
Zoom in
Previous page
1/22
Next page
E8
8. NAIT XS 2
The NAIT XS 2 is a very high performance stereo integrated amplier that combines a
preamplier providing six line-level analogue inputs with a power amplier rated at 70 Watts
per channel. The NAIT XS 2 can be controlled by either its remote handset or by a front panel
mounted volume knob and mute and input selection buttons. The NAIT XS 2 remote handset
is described in Section 15 of this manual. A front panel 6.3mm jack socket enables the use of
headphones with the NAIT XS 2.
A variety of power supply upgrade, alternative preamplier and alternative or additional power
amplier options are possible for the NAIT XS 2. A diagram illustrating one option is shown in
Section 10. If no power supply or alternative amplier options are to be employed, the NAIT XS
2 preamp/power amp link plug, supplied in the accessory pack, must be tted to the rear panel
“preamp out” and “power amp in” sockets. The link plug is shown tted in Diagram 9.2.
Your NAIT XS 2 should be installed on a dedicated equipment stand intended for the purpose.
Do not stand it directly on top of another item of equipment. Care should be taken to ensure
that it is level. The amplier should be installed in its nal location before connecting cables or
switching on. Ensure that the volume is turned down before switching on.
8.1 Mains Power Connection
Connect the NAIT XS 2 to a mains power socket using either
the mains cable supplied or a Naim Power-Line.
8.2 Signal Inputs
The NAIT XS 2 front panel input buttons select the source input
signal to be routed to the integral power amplier and the
loudspeakers or headphones. The six buttons are labelled cd,
tuner, hdd (hard disk drive), av, aux 1 and aux 2.
The cd, tuner, hdd and av input buttons correspond to
parallel DIN and RCA phono input sockets on the rear panel,
while the aux 1 input button corresponds only to a pair of
RCA phono sockets.
Note: The hdd and av sockets carry both inputs and
outputs. See Section 8.4 for more information.
The aux 2 input button corresponds to a DIN input socket
on the rear panel. The aux 2 DIN socket also carries a
power supply output intended to power a Naim Stageline or
SuperLine phono preamplier.
Note: For optimum sound quality DIN sockets should
always be used in preference to RCA phono sockets.
Note: Where an input has DIN and phono socket options
only one should be connected at any one time.
Always use high quality interconnect cables to connect
sources to inputs. The Naim Hi-Line will produce the best
results.
8.3 Speaker Outputs
A set of stereo speaker connection sockets is provided on
the rear panel. Custom Naim loudspeaker connectors are
supplied to make the connection and in order to comply
with current European safety regulations these should
always be used. Naim speaker cable will provide the best
results, however, a wide range of speaker cable types can
be used without risk of damage to the amplier.
Ensure when connecting speakers that they are “in phase.
That is, the positive and negative connection orientation at
both the speaker and amplier ends of the cable is the same
for both channels.
8.4 av and hdd Outputs
The NAIT XS 2 av and hdd inputs have associated outputs
that enable the selected input signal to be routed externally;
to an audio recording component for example.
Note: The av and hdd outputs remain active while
their corresponding inputs are selected. Take care that
a feedback loop is not inadvertently created by the
simultaneous selection of input and output.
8.5 Headphone Output
The NAIT XS 2 headphone output is able to drive the
majority of headphone types. The 6.3mm (1/4”) jack socket,
rather than the smaller 3.5mm jack socket, provides more
reliable connection and potentially higher sound quality.
Most high-quality headphones are supplied with an adaptor
that enables use with either 3.5mm or 6.3mm jack sockets.
Inserting a headphone plug will mute the NAIT XS 2 speaker
outputs. Removing the headphone plug will restore the
outputs.
8.6 AV Bypass
The NAIT XS 2 can be integrated within a multi-channel
home theatre system, driving the front left and right channel
speakers, by engaging its AV Bypass mode. AV Bypass
mode enables a home theatre processor to take over volume
control of signals connected to the NAIT XS 2 av input. It is
engaged using the switch on the rear panel. The
NAIT XS 2 volume control indicator will extinguish when AV
Bypass mode is engaged and the av input is selected. The
remote handset volume control will also be disabled.
Note: The NAIT XS 2
incorporates an AV Bypass
switch on its rear panel.
The switch should only be
set to “On” if the amplifier
is to be used in conjunction
with an AV processor in a
home theatre system. In
all other installations the
AV Bypass switch should
be set to “Off”. Speaker
and amplifier damage
may occur if a signal is
inadvertently connected
to the NAIT XS 2 av input
while the AV Bypass switch
is “On.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Naim NAIT 5SI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Naim NAIT 5SI in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Naim NAIT 5SI

Naim NAIT 5SI User Manual - German - 22 pages

Naim NAIT 5SI User Manual - Dutch - 22 pages

Naim NAIT 5SI User Manual - French - 22 pages

Naim NAIT 5SI User Manual - Italian - 22 pages

Naim NAIT 5SI User Manual - Polish - 22 pages

Naim NAIT 5SI User Manual - Spanish - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info