Manual NAD VISO TWO (page 29 of 34) (English)

602923

Zoom out

Zoom in

1/34

LEARNING CODES FROM OTHER REMOTES

Begin by positioning the HTR 6 “nose-to-nose” with the source remote so

the two devices’ infrared windows are about 2 inches apart.

• Enter Learning Mode: On the HTR 6, simultaneously press-and-hold for

3 seconds both a Device Selector key and the [ ] key until the Learn

LED at the center of the HTR 6 turns steady green.

• Press the HTR 6’s function key you wish to teach a command; the Learn

LED will turn amber.

• Press-and-hold the function key on the source remote: The HTR 6’s

Learn LED will icker amber for a second or two, then turn solid green.

The command is learned.

• Press the HTR 6’s Device Selector key again to exit the learning mode.

If the Learn LED does not icker amber you may need to vary the distance

between the remotes. If the Learn LED turns red rather than green, that

particular command of that source remote command could not be learned.

CANCEL OPERATION

You can cancel conguring a key, by pressing the active Device Selector key

before the learn process is complete; the Learn LED will turn red.

Example: Learning “DVD Pause”

Position the HTR 6 and your DVD player’s remote as described above.

• On the HTR 6, simultaneously press-and-hold [DVD] and [ ]; the Learn

LED turns steady green.

• Press the HTR 6’s [ ] key; the Learn LED turns amber.

• Press-and-hold the DVD player’s remote’s pause key; the HTR 6’s Learn

LED ickers amber and then turns solid green. The command is learned.

• Press [DVD] again to exit the learning mode.

PUNCH-THROUGH

The HTR 6’s “punch-through” function allows you to retain a function key

from one Device Select “page” to another, so that, for example, the AMP

[SURR MODE] function might still control the VISO TWO when the DVD

Device Selector page is active.

NOTE

 TheHTR6’s[VOL]keysarepre-programmedas“punched-through”

forallDeviceSelectpages:[VOL]willoperatetheVISOTWO’svolume

regardlessofthecurrentlyselecteddevice.The[SUB]levelcontrolis

similarlypre-programmedaspunched-through.

To set a punch through, after entering the Learning Mode, and pressing the

desired key to be punched through, simply press the device key twice of

the device to punch through to. The status LED will turn green; press the

Device Selector key again to exit Learning Mode.

Example: Punch-through AMP [SURR MODE] key to the DVD “page”

• On the HTR 6, simultaneously press-and-hold [DVD] and [ ]; the Learn

LED turns steady green.

• Press [SURR MODE]; the Learn LED turns amber.

• Press [AMP] twice; the Learn LED turns green.

• Press [DVD] again to exit the learning mode.

NOTE

 TheHTR6controlkeys[ ],[ ],[ ],[ / / / ]and[ ]arenot

punch-throughfunctionkeys.Tousethemfordiscplaybackpurposes,make

surethatHTR6’sDEVICESELECTORissetto“DVD”.

COPY COMMAND FROM ANOTHER BUTTON

You may copy a command from any HTR 6 key to any other key. To copy a key

function, after entering the Learning Mode, and pressing the desired key to be

copied to, simply press the device key from which you wish to copy, having rst

pressed its Device Selector key if it resides on another “page.” The status LED will

turn green; press the Device Selector key again to exit Learning Mode.

Example: Copy the Pause command from the CD page to the AMP [ ]

key:

• On the HTR 6, simultaneously press-and-hold [AMP] and [ ]; the Learn

LED turns steady green.

• Press [ ] (pause); the Learn LED turns amber.

• Press [CD]; press [ ] (pause); the Learn LED turns green.

• Press [AMP] again to exit the learning mode.

NOTE

 Thecopyandpunch-throughfunctionsaresimilar.However,ifyou

copyacommandandthensubsequentlydelete,orover-writethe

original(source-key)command,thecopied-tokey’scommandremains

unchanged.Ifyoupunch-throughtoacommandandthendeleteor

over-writetheoriginalkey,thepunched-throughfunctionsalsochange

accordingly.

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued

automatically from a single keypress. You might use a macro to automate

a simple command sequence, such as, “Turn on the DVD player” and

then press “play”. Or you might compose an elaborate macro to power

up an entire system, select a source, choose a Listening Mode, and begin

playback—again, all from a single keypress. The HTR 6 can store one macro

on each of its function keys (these exclude the Device Selector keys).

NOTE

 Macrosareindependentofthecurrentlyselecteddevice.

RECORDING MACROS

To record a macro, simultaneously press-and-hold for 3 seconds both the

[MACRO] key and the HTR 6 function key to which you wish to assign the

macro, until the status LED turns green. The macro button will also light up.

Press the sequence of function keys to be recorded into the macro, being

sure to rst press the requisite Device Selector key for each function (you

may switch devices while recording the macro as many times as necessary),

allowing you to create macro containing commands from more than one

Device Selector “page.”

When you have nished entering the desired command sequence, press

[MACRO] again to store the macro; the Learn LED and [MACRO] key

illumination will turn o.

NOTE

 Eachmacrocanstoreamaximumof64commandsteps.Ifyouexceed

thisnumber,themacrowillbestoredautomaticallyafterthe64th

command is added.

Example: Record a Macro to the [0] key to Turn on the VISO TWO, Select

the DVD Input, and Commence Playback:

• On the HTR 6, simultaneously press-and-hold [MACRO] and [0] (numeric

zero); the Learn LED turns steady green.

• Press [AMP]; press [ON]; press [1] (“DVD”); press [DVD]; press [ ] (Play)

- the Learn LED blinks as each step is added.

• Press [MACRO] again to exit the macro-record mode.

To clear a macro, perform the above steps without entering any functions.

OPERATION

USING THE HTR 6 REMOTE CONTROL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD VISO TWO in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD VISO TWO

NAD VISO TWO User Manual - German - 34 pages

NAD VISO TWO User Manual - Dutch - 34 pages

NAD VISO TWO User Manual - French - 36 pages

NAD VISO TWO User Manual - Italian - 34 pages

NAD VISO TWO User Manual - Swedish - 34 pages

NAD VISO TWO User Manual - Spanish - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD VISO TWO Manual

Product: