Manual NAD T977 (page 4 of 66) (English, German, Dutch, French, Italian, Swedish, Spanish)

602921

Zoom out

Zoom in

1/66

INTRODUCTION

GETTING STARTED

QUICK START

In case you simply cannot wait to experience the performance of your new

NAD T 977 Seven Channel Power Amplier, the following QUICK START

guide is recommended to help you get started.

Ensure that the T 977 is unplugged before making any connections. It is

also advisable to power-down or unplug all associated components while

making or breaking any signal or AC power connections.

1 Set the following initial conditions:

· Preamplier’s volume level set to minimum

· Each channel INPUT level controls of T 977 set to minimum (MIN)

2 Connect your speakers to the SPEAKER terminals of T 977. Note

suggested speaker connections as reected in the rear panel channel

allocations.

3 Connect your Preamplier’s PRE OUT to the T 977 rear panel’s INPUT

port.

4 Plug-in to a mains power source the T 977’s supplied mains power cord.

Before connecting the plug to the mains powers source, connect rmly

rst the other end to T 977’s AC Mains input socket. The T 977 goes to

standby mode as shown by the amber status condition of the Standby

LED.

5 Plug-in also to a mains power source the Preamplier’s mains power

cord. Power up your Preamplier ahead of the T 977.

6 Press STANDBY button to switch ON the T 977 from standby mode. The

Standby LED indicator will turn from amber to blue. When the T 977 is

switched ON from standby mode, the Channel Status LEDs will initially

turn red and then eventually turn blue. The T 977 is ready for operation.

7 Adjust the corresponding T 977 INPUT LEVEL CONTROL and/or

Preamplier’s volume control according to desired listening levels.

SAVE THE PACKAGING

Please save the box and all of the packaging in which your T 977 arrived.

Should you move or otherwise need to transport your T 977, this is by far

the safest container in which to do so. We’ve seen too many otherwise

perfect components damaged in transit for lack of a proper shipping

carton, so please: Save that box!

NOTES ON INSTALLATION

Your NAD T 977 should be placed on a rm, level surface. Avoid placing the

unit in direct sunlight or near sources of heat and damp. Allow adequate

ventilation. Do not place the unit on a soft surface like a carpet. Avoid

placing the T 977 inside a closed cabinet that is not well ventilated as this

may compromise the T 977’s performance and reliability.

Ensure that the T 977 is unplugged before making any connections. For

best performance, use quality speaker leads of 16 gauge (1.5mm) thickness

or more. If the unit is not going to be used for some time, disconnect the

plug from the mains power source.

Should water get into your T 977, immediately press the Standby button

and then disconnect the mains power cord from the mains power source.

Have the unit inspected by a qualied service technician before attempting

to use it again.

DO NOT REMOVE THE COVER; THERE ARE NO USERSERVICEABLE

PARTS INSIDE.

Use a dry cloth for cleaning.

BARE WIRES AND PIN CONNECTORS

WARNING: The terminals marked with this symbol

are hazardous live. External wiring connected to these

terminals requires installation by an instructed person or

the use of ready-made leads or cords.

Bare wires and pin sockets should be inserted into the hole in the shaft

of the terminal. Unscrew the speaker terminal’s plastic bushing until the

hole in the screw shaft is revealed. Insert the pin or bare cable end into

the hole and secure the cable by tightening down the terminal’s bushing.

Ensure bare wire from the speaker cables does not touch the back panel or

another socket. Ensure that there is only 1/2” (1cm) of bare cable or pin and

no loose strands of speakers wire.

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

T977_eng_OM_v04.indd 4 17/04/2012 9:28am

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD T977 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 3,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD T977 Manual

Product: