602906
9
Zoom out
Zoom in
Previous page
1/40
Next page
6 DAB MODULE INPUT (230V version model only)
The T 748 is compatible only with the NAD DAB Adaptor module
models DB 1 or DB 2.
• Plug-in the other end of the Mini-Din connector from the NAD DAB
Adaptor module output port into this socket.
• With DAB, you can receive CD-like quality programs without any
annoying interference and signal distortion.
• Refer also to the “LISTENING TO DAB RADIO” segment of the
“OPERATION” section.
NOTE
The external NAD DAB Adaptor module is not supplied with your T 748.
7 HDMI (HDMI 1-4, HDMI MONITOR OUT)
• Connect the sets of HDMI input to the HDMI OUT connectors of
source components such as DVD player, BD player or HDTV satellite/
cable box. Connect the HDMI Monitor OUT to a HDTV or projector
with HDMI input.
WARNING
Before connecting and disconnecting any HDMI cables, both the T 748
and the ancillary source must be powered OFF and unplugged from the
AC outlet. Failure to observe this practice may cause permanent damage
to all equipment connected via HDMI sockets.
8 DIGITAL AUDIO (COAXIAL 1-2, OPTICAL 1-2)
• Connect to the corresponding optical or coaxial digital output of
sources such as CD or BD/DVD players, digital cable box, digital
tuners and other applicable components.
• Coaxial and Optical digital input association is congurable via the
Source Setup item of the Setup Menu OSD.
9 IR IN
• This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 748 from a remote location.
10 MP DOCK
The T 748 is equipped with a data port in the rear panel where an
optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later
variants can be plugged in.
• Connect the “MP DOCK (DATA PORT)” jack of the T 748 to the
corresponding “DATA PORT socket of the optional NAD IPD model.
• AUDIO 2 IN and S-VIDEO IN are the assigned default ports for the
audio/video output of the separately sold NAD IPD (NAD IPD Dock
for iPod) 1, NAD IPD 2 and later variants.
• Refer also to the “LISTENING TO YOUR iPod PLAYER” segment of the
“OPERATION” section.
NOTE
The NAD IPD Dock for iPod is not supplied with your T 748.
11 RS 232
NAD is a certied partner of AMX and Crestron and fully supports
these external devices. Check out the NAD website for information
about AMX and Crestron compatibility with NAD. See your NAD audio
specialist for more information.
• Connect this interface using RS-232 serial cable (not supplied) to
any Windows compatible PC to allow remote control of the T 748
via compatible external controllers.
12 AUDIO PRE-OUT
• The AUDIO PRE- OUT makes it possible to use the T 748 as a pre-
amplier to external power ampliers for some or all channels.
Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and
SURR-BR to the respective channel input of a power amplier or
ampliers driving the corresponding applicable speakers.
• Unlike the full range channels, there is no power amplier built-into
the T 748 for a subwoofer. Connect the SUBW output to powered
(“active”) subwoofers or to power amplier channels driving a
passive system.
NOTE
Never connect both the external amplier and T 748’s speaker outputs to
the same set of speakers.
13 SPEAKERS
• Connect the respective speaker’s FRONT L, FRONT R, CENTER,
SURR R, SURR L, SURR-BACK L, and SURR-BACK R channels to their
corresponding loudspeakers. Make sure the “+” (red) terminal and
“-” (black) terminal are connected to the corresponding “+” and “-”
terminals of the loudspeaker. Use extra care to ensure that no stray
wires or strands cross between posts or terminals at either end.
• The T 748 is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 8 ohms minimum
per speaker.
NOTE
Use stranded wire of at least 16 gauge (AWG). Connections to the T 748 can
be made with banana-type plugs. Bare wire or pins can also be used by
loosening the terminal’s plastic nut, making a clean, neat connection, and
re-tightening carefully. To minimize the danger of short circuit, ensure that
only 1/2-inch of exposed wire or pin is employed when connecting.
14 AC MAINS INPUT
The T 748 comes supplied with a separate detachable mains power
cord. Before connecting the plug to the mains power source, ensure
that it is rmly connected to the T 748’s AC Mains input socket rst.
• Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V
version models only) or 230V 50 Hz (for 230V version models only).
• Always disconnect the mains power plug from the mains power
source rst, before disconnecting the cable from the T 748’s AC
Mains input socket.
15 SWITCHED AC OUTLET
This convenience outlet can supply switched power to another
component or accessory.
• The total draw of all devices connected to this outlet must not
exceed 100 watts.
• It is powered ON and OFF by the front panel STANDBY button or by
the AVR 4’s ON and OFF keys.
IDENTIFICATION OF CONTROLS
REAR PANEL
9
ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD T748v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD T748v2 in the language / languages: English as an attachment in your email.

The manual is 3,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T748v2

NAD T748v2 User Manual - German - 40 pages

NAD T748v2 User Manual - Dutch - 40 pages

NAD T748v2 User Manual - French - 40 pages

NAD T748v2 User Manual - Italian - 40 pages

NAD T748v2 User Manual - Portuguese - 40 pages

NAD T748v2 User Manual - Swedish - 40 pages

NAD T748v2 User Manual - Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info