602917

NAD T 775 Manual

39
Zoom out
Zoom in
Previous page
1/46
Next page
MACRO COMMANDS
A “macro” command is a series of two or more remote codes issued automatically from a single
keypress. You might use a macro to automate a simple command sequence, such as, “Turn on the DVD
player and then press PLAY”. Or you might compose an elaborate macro to power up an entire system,
select a source, choose a Listening Mode, and begin playback—again, all from a single keypress. The
HTR 3 can store one macro on each of its function keys (these exclude the Device Selector keys).
NOTE
Macrosareindependentofthecurrentlyselecteddevice.
RECORDING MACROS
To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 3
function key to which you wish to assign the macro, until the status LED turns green. The macro
button will also light up.
Press the sequence of function keys to be recorded into the macro, being sure to rst press the
requisite Device Selector key for each function (you may switch devices while recording the macro as
many times as necessary), allowing you to create macro containing commands from more than one
Device Selector “page.”
When you have nished entering the desired command sequence, press [MACRO] again
to store the macro; the Learn LED and [MACRO] key illumination will turn o.
NOTE
Eachmacrocanstoreamaximumof64commandsteps.Ifyouexceedthisnumber,themacrowill
bestoredautomaticallyafterthe64thcommandisadded.
Example: Record a Macro to the [0] key to Turn on the T 775, Select “Input 1” (Source 1), and
Commence Playback of connected Source 1 device (as in DVD player):
• On the HTR 3, simultaneously press-and-hold [MACRO] and [0] (numeric zero); the Learn LED turns
steady green.
• Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [DVD]; press [ ] (Play) - the Learn LED
blinks as each step is added.
• Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
EXECUTING MACROS
To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. While it
remains lit, press an HTR 3 key to which a macro has previously been stored.
The corresponding macro will run; as each step executes, its “parent” Device Selector’s key ashes lights
briey; when execution is nished, the [MACRO] key illumination goes out. Pressing any other HTR 3
key while a macro is executing will abort the macro. Remember that you must hold the HTR 3 so that
its infrared emitter can activate the target components.
NOTE
Whenamacroexecutes,a1seconddelayisautomaticallyinsertedbetweenitscommands.If
youneedmorethana1seconddelaybetweenparticularcommands—forexample,topermita
componenttopowerupcompletely—youcanrecord“empty”stepsintothemacrobychanging
DeviceSelector“pages”withoutenteringactualcommandfunctions.
BUTTON ILLUMINATION TIMEOUT
The HTR 3’s key-illumination can be set to remain lit for 0-9 seconds. The default value is 2 seconds. To
set the illumination timeout, simultaneously press-and-hold for 3 seconds both the HTR 3’s [DISP] and
the [0-9] key, with the digit corresponding to the desired timeout duration; the Learn LED will ash
twice to conrm the new setting. When set to zero, the illumination will not turn on at all.
NOTE
KeyilluminationisthebiggestdrainontheHTR3’sbatteries.Ashortkey-illuminationtimeoutwill
extendbatterylifeappreciably;turningitoaltogether(setitto0seconds)willlengthenitstill
further.
OPERATION
USING THE HTR 3 REMOTE CONTROL
39
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD T 775 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 775 in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 775

NAD T 775 User Manual - German - 44 pages

NAD T 775 User Manual - Dutch - 44 pages

NAD T 775 User Manual - French - 46 pages

NAD T 775 User Manual - Italian - 44 pages

NAD T 775 User Manual - Swedish - 42 pages

NAD T 775 User Manual - Spanish - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info