Manual NAD T 754 (page 27 of 32) (English)

606564

Zoom out

Zoom in

1/32

2727

ENGLISH

USING THE HTR 2 REMOTE CONTROL

PUNCH-THROUGHPUNCH-THROUGH

PUNCH-THROUGH

The HTR 2’s “punch-through” function allows you to retain a function key from one Device Select “page”

on another, so that, for example, the AMP [SURR MODE] function might still control the T 754 when the DVD

Device Selector page is active

NOTE: The HTR 2’s [VOL] keys are pre-programmed as “punched-through” for all Device Select pages:

[VOL] will operate the T 754’s master-volume regardless of the currently selected device. The [SURR.]

[CENTER,] and [SUB] Channel Volume controls similarly are pre-programmed as punched-through.

To set a punch through, after entering the Learning Mode, and pressing the desired key to be punched-

through, simply press the device key twice of the device to punch through to. The status LED will turn green;

press the Device Selector key again to exit Learning Mode.

Example: Punch-through the from the DVD “page” to the AMP [SURR MODE] key:

• On the HTR 2, simultaneously press-and-hold [DVD] and [•] (record); the Learn LED turns steady green.

• Press [SURR MODE]; the Learn LED turns amber.

• Press [AMP] twice; the Learn LED turns green.

• Press [DVD] again to exit the learning mode.

COPY A COMMAND FROM ANOTHER KEYCOPY A COMMAND FROM ANOTHER KEY

COPY A COMMAND FROM ANOTHER KEY

You may copy a command from any HTR 2 key to any other. To copy a key function, after entering the

Learning Mode, and pressing the desired key to be copied to, simply press the device key from which you

wish to copy, having first pressed its Device Selector key if it resides on another “page.” The status LED will

turn green; press the Device Selector key again to exit Learning Mode.

Example: Copy the Pause command from the CD page to the AMP [

] key:

• On the HTR 2, simultaneously press-and-hold [AMP] and [•] (record); the Learn LED turns steady green.

• Press [

] (pause); the Learn LED turns amber.

• Press [CD]; press [

] (pause); the Learn LED turns green.

• Press [AMP] again to exit the learning mode.

NOTE: The copy and punch-through functions are similar. However, if you copy a command and then

subsequently delete, or over-write the original (source-key) command , the copied-to key’s command

remains unchanged. If you punch-through to a command and then delete or over-write the original key,

the punched-through functions also change accordingly.

MACRO COMMANDSMACRO COMMANDS

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued automatically from a single keypress.

You might use a macro to automate a simple command sequence, such as, “Turn on the DVD player and then

press ‘play.’” Or you might compose an elaborate macro to power up an entire system, select a source,

choose a Listening Mode, and begin playback—again, all from a single keypress. The HTR 2 can store one

macro on each of its function keys (these exclude the Device Selector keys).

NOTE: Macros are independent of the currently selected device.

RECORDING MACROSRECORDING MACROS

RECORDING MACROS

To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 2

function key to which you wish to assign the macro, until the status LED turns green. The macro button will

also light up. Press the sequence of function keys to be recorded into the macro, being sure to first press

the requisite Device Selector key for each function (you may switch devices while recording the macro as

many times as necessary), allowing you to create macro containing commands from more than one Device

Selector “page.” When you have finished entering the desired command sequence, press [MACRO] again

to store the macro; the Learn LED and [MACRO] key illumination will turn off.

NOTE: Each macro can store a maximum of 64 command steps. If you exceed this number, the macro will

be stored automatically after the 64th command is added.

Example: Record a Macro to the [0] key to Turn on the T 754, Select the DVD Input, and Commence

Playback:

• On the HTR 2, simultaneously press-and-hold [MACRO] and [0] (numeric zero); the Learn LED turns

steady green.

• Press [AMP]; press [ON]; press [1] (red “DVD”); press [DVD]; press [play] (the Learn LED blinks as

each step is added).

• Press [MACRO] again to exit the macro-record mode.

To clear a macro, perform the above steps without entering any functions.

EXECUTING MACROSEXECUTING MACROS

EXECUTING MACROS

To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. While it remains

lit, press an HTR 2 key to which a macro has previously been stored. The corresponding macro will run; as

each step executes, its “parent” Device Selector’s key flashes lights briefly; when execution is finished, the

[MACRO] key illumination goes out. Pressing any other HTR 2 key while a macro is executing will abort the

macro. Remember that you must hold the HTR 2 so that its infrared emitter can activate the target

components.

NOTE: When a macro executes, a 1 second delay is automatically inserted between its commands. If you

need more than a 1 second delay between particular commands—for example, to permit a component to

power up completely—you can record “empty” steps into the macro by changing Device Selector “pages”

without entering actual command functions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 754 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 754

NAD T 754 User Manual - German - 32 pages

NAD T 754 User Manual - Dutch - 32 pages

NAD T 754 User Manual - French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD T 754 Manual

Product: