Manual NAD T 754 (page 26 of 32) (English)

606564

Zoom out

Zoom in

1/32

2626

USING THE HTR 2 REMOTE CONTROL

• Controls up to 8 devices.

• 44 function keys.

• Learns up to 352 commands.

• Records up to 44 macros with a maximum of 64 commands each.

• Configurable punch-through.

• Key illumination with programmable timeout.

• Upgradable.

• Contains pre-programmed library of NAD remote codes.

The NAD HTR 2 is ready to operate the T 754 receiver right out of the box, but it is really eight remotes in

one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote-

control codes to be transmitted by the remaining 44 keys. You may “teach” codes from any infrared-remote-

controlled component, regardless of brand, to any or all of these. Obviously, the most logical system is that

you teach the codes from your DVD player to the [DVD] Device Selector “page,” your television’s codes to

the [TV] “page,” and so on, but there is no required scheme: You may load any commands to any key on

any page (see “Learning Codes From Other Remotes,” below).

The HTR 2 is already preprogrammed with a full complement of commands for the T 754 receiver on its

[AMP] Device Selector page, and as well as with library commands to operate most NAD-brand DVD, CD, or

TAPE components on the corresponding Device Selector “pages.” These default commands are permanent:

Even if you teach the HTR 2 new commands to take their place, the underlying library commands remain in

place and can easily be recalled should you add an NAD component to your system later (see “Delete

Mode”, below).

NOTE: For use with the T 754, it should not be necessary to re-program any keys on the HTR 2 [AMP]

page. However, in order for the HTR 2 to control your specific NAD-brand components you may need to

load one or more different code-libraries; see “Loading Code Libraries,” below.

CONTROLLING THE T 754

The HTR 2 is divided into two main sections. Eight Device Selector keys at the top—[AMP], [DVD,] [TV,] and

so on—set the handset’s remaining keys to a “page” of commands to control a particular component. A

Device Select key determines only what component the HTR 2 will command; it does not perform any

function on the receiver. All of the remaining keys are function keys that can “learn” control codes from

virtually any infrared remote controller, allowing you to teach the codes of your equipment, regardless of

brand, to the HTR 2.

However, the HTR 2 is already preprogrammed to operate the T 754. All of the function keys on the [AMP]

Device Selector “page” perform T 754 functions. (The HTR 2 can also command many other NAD compo-

nents, from its [DVD,] [CD,] [TUNER,] and [TAPE] pages.)

It is important to note that certain HTR 2 keys perform different functions depending on the selected Device

Selector “page.” The color of the Device Selector key-labeling corresponds to the labeling of the function

keys. Most centrally, the red [AMP] Device Selector “page” corresponds to the red input-select labeling

adjacent to the numeric keys: When the HTR 2’s [AMP] Device Selector page is active, these keys select the

receiver inputs. Similarly, the purple [DVD] Device Selector “page” corresponds to several purple labels, the

green [TV] page to green labels, and so on.

LEARNING CODES FROM OTHER REMOTESLEARNING CODES FROM OTHER REMOTES

LEARNING CODES FROM OTHER REMOTES

Begin by positioning the HTR 2 “nose-to-nose” with the source remote so the two devices’ infrared windows

are about 2 inches apart.

• Enter Learning Mode: On the HTR 2, simultaneously press-and-hold for 3 seconds both a Device Selector

key and the [•] “record” key (just below the [DISP] key), until the Learn LED at the center of the HTR 2

turns steady green.

• Press the HTR 2’s function key you wish to teach a command; the Learn LED will turn amber.

• Press-and-hold the function key on the source remote: The HTR 2’s Learn LED will flicker amber for a

second or two, then turn solid green. The command is learned.

• Press the HTR 2’s Device Selector key again to exit the learning mode.

If the Learn LED does not flicker amber you may need to vary the distance between the remotes.

If the Learn LED turns red rather than green, that particular command of that source remote command

could not be learned.

Cancel Operation:

You can cancel configuring a key, by pressing the active Device Selector key before the learn is complete;

the Learn LED will turn red.

Example: Learning “DVD Pause”:

Position the HTR 2 and your DVD player’s remote as described above.

• On the HTR 2, simultaneously press-and-hold [DVD] and [•]; the Learn LED turns steady green.

• Press the HTR 2’s [

] (pause) key; the Learn LED turns amber.

• Press-and-hold the DVD player’s remote’s pause key; the HTR 2’s Learn LED flickers amber and then

turns solid green. The command is learned.

• Press [DVD] again to exit the learning mode.

SPECIFICASPECIFICA

SPECIFICA

TIONSTIONS

TIONS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 754 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 754

NAD T 754 User Manual - German - 32 pages

NAD T 754 User Manual - Dutch - 32 pages

NAD T 754 User Manual - French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD T 754 Manual

Product: