602914
13
Zoom out
Zoom in
Previous page
1/20
Next page
13
ENGLISH
FRANÇAISDEUTSCHNEDERLANDSESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
8. REC/Z2: This output is a steady state line-level output. Connect this output to recording
equipment such as an audio tape deck or an A/D Converter recorder.
One may also connect this output to an auxiliary piece of audio equipment such as an
integrated amplifier for multi-zone operation. In such a case, use this output in conjunction
with the ZR3 remote control and IR IN. (refer to the IR IN section below).
9. SPEAKERS A: Connect speakers with impedance of 4 Ohms or greater. Connect the right
speaker to the terminals market 'R +' and 'R-' ensuring that the 'R+' is connected to the
'+' terminal on your loudspeaker and the 'R-' is connected to the loudspeaker's '-' terminal.
Connect the terminals marked 'L+' and 'L-' to the left speaker in the same way. When
using both SPEAKERS A and SPEAKERS B connect speakers of impedance 8 Ohms or
greater.
10. SPEAKERS B: Connect speakers with impedance of 4 Ohms or greater. Connect the right
speaker to the terminals market 'R +' and 'R-' ensuring that the 'R+' is connected to the
'+' terminal on your loudspeaker and the 'R-' is connected to the loudspeaker's '-' terminal.
Connect the terminals marked 'L+' and 'L-' to the left speaker in the same way. When
using both SPEAKERS A and SPEAKERS B connect speakers of impedance 8 Ohms or
greater.
NOTES: When connecting both SPEAKERS A and B, connect speakers with impedance no
less than 8 Ohms.
Always use heavy duty (16 gauge/2 square mm or thicker) stranded wire to connect
loudspeakers to your M3.
The high current binding post terminals can be used as a screw terminal for cables
terminating in spade or pin connectors or for cables with bare wire ends.
SPADE CONNECTORS (Figure 3)
These should be slotted under the terminal's screw bushing, which is then fully tightened.
Ensure the connector is tightly secured and there is no danger of bare metal from spade
connectors touching the back panel or another connector as this may cause damage.
BARE WIRES AND PIN CONNECTORS (Figure 3)
Bare wires and pin connectors should be inserted into the hole in the shaft of the terminal.
Unscrew the speaker terminal's plastic bushing until the hole in the screw shaft is revealed.
Insert the pin or bare cable end into the hole and secure the cable by tightening down the
terminal's bushing.
Avoid any danger of bare metal from the speaker cables touching the back panel or
another connector. Ensure that there is only 1/2" (1cm) of bare cable or pin and no loose
strands of speakers wire.
11. IR IN & IR OUT 2: Use these 3.5 mm mini-jack connectors to pass commands from other
units with similar IR (infrared) connectors. Daisy-chain other hi-fi system's IR outputs to the
M3's IR IN and then M3's IR OUT 2 to other hi-fi systems' IR inputs so that control of a
whole system via a single remote control facility is from one unit with a single IR
connection.
NOTES:
IR OUTPUT 1 is hard wired to the M3’s front panel IR sensor. Only Daisy-chain the IR IN with
IR OUT 2 when connecting the M3 as part of a series IR configuration.
Your custom installer or dealer can assist you in the proper setup and configuration of
infrared multi-room hi-fi systems.
About the M3 Dual Mono Integrated Amplifier
Setup
M3 10262005.qxd 1/3/2006 2:49 PM Page 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M3e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M3e in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M3e

NAD M3e User Manual - German - 20 pages

NAD M3e User Manual - Dutch - 20 pages

NAD M3e User Manual - French - 20 pages

NAD M3e User Manual - Italian - 20 pages

NAD M3e User Manual - Portuguese - 20 pages

NAD M3e User Manual - Swedish - 20 pages

NAD M3e User Manual - Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info