667811
14
Zoom out
Zoom in
Previous page
1/24
Next page
SUB MODE
Set the subwoofer mode to either mono or stereo setting.
Mono: Select this setting when using one subwoofer. At mono mode,
the left and right channels are summed in the low pass subwoofer
output to drive a single subwoofer.
Stereo: Select this setting when using two subwoofers, one for the left
channel and one for the right channel.
MAIN FREQUENCY 40Hz to 200Hz and Full
MAIN TRIM 12.0dB to 0.0dB
Crossover allows easy bi-amplication or subwoofer integration
by adding the required lters to redirect bass frequencies to the
subwoofer.
Frequencies from 40Hz to 200Hz and Full can be selected, with the high
pass signal sent to the amplier section and the low pass signal sent to
Subwoofer Out.
SUB FREQUENCY 40Hz to 200Hz and Full
SUB TRIM 12.0dB to 0.0dB
Selected subwoofer crossover frequency and below will be redirected
to subwoofer output.
Sub trim provides exact volume matching of the subwoofer level to the
main speaker level.
NOTE
Since the low pass lter is already implemented in the M32, the
subwoofer should be set to the highest frequency crossover setting
available or bypassed if it also includes a crossover function.
SOURCE SETUP
Source Setup makes it possible to select a Source and enable or disable it
as desired. The optional DD AP-1 (Direct Digital Analog Phono), DD HDM-1
(HDMI) and MDC BluOS modules must be installed to select Sources like
Single-ended, Balanced, Digital HDMI 1 or BluOS. If the applicable module
is not installed, the corresponding sources will not be available from the
Source Setup menu selection.
--- : Non-MDC or built-in sources.
Slot A : Location slot of the Source module (MDC) in the rear panel.
Cable TV : Source name for Line 1 input. Source name can be changed in
the “Name” section shown below.
When a Slot line item is selected, the following menu options will be displayed.
Enabled: Source input can be enabled (ON) or disabled (OFF).
Name: Source input name. Selecting this line item will lead to the menu
keyboard where one can type the preferred name for the current source.
VOLUME CONTROL
The M32 VOLUME control function is dependent upon the Volume
Control” menu setting. Volume control can either be set to “Fixed” or
Variable. Select “Save” to store selected Volume Control” and “Fixed Level”
or “Variable settings.
Fixed
If Volume Control” is set to “Fixed”, audio output level is xed and the
M32’s volume control is bypassed. With “Fixed” volume control setting,
the M32 becomes like a basic amplier with volume controlled by an
external device.
Set “Fixed Level” to desired preset dB level. Audio output is xed
to the selected level after saving the setting. Audio output level
will not change when using the Volume control or HTRM 2’s
[VOLR/T].
At “Fixed Level” setting, the volume control or HTRM 2’s [VOL R/T]
will have no eect and eectively disabled.
Variable
When set to Variable, audio output level is directly adjustable using
the volume control or HTRM 2’s [VOL R/T].
The following additional menu options are included if LINE 1 or LINE 2
input is selected.
OPERATION
USING THE M32
14
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M32 DirectDigital DAC Amplifier at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M32 DirectDigital DAC Amplifier in the language / languages: English as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M32 DirectDigital DAC Amplifier

NAD M32 DirectDigital DAC Amplifier User Manual - German - 24 pages

NAD M32 DirectDigital DAC Amplifier User Manual - Dutch - 24 pages

NAD M32 DirectDigital DAC Amplifier User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info