562261
9
Zoom out
Zoom in
Previous page
1/38
Next page
Below is a table of sample combination settings with respect to
switching ON the M17 from standby mode and vice versa.
+12V
TRIGGER IN
(OFF/AUTO)
+12V
TRIGGER(IN)
(item 5)
AUTO
TRIGGER IN
FRONT
PANEL
o (STANDBY)
HTRM 2 (ON/
OFF)
M17 POWER
MODE STATE
AUTO +12V Main, All ON ON Operating
mode
AUTO +12V Main, All OFF OFF Operating
mode
AUTO 0V Main, All ON/OFF ON/OFF Standby
mode
AUTO 0V Zone 2,
Zone 3 or
Zone 4
ON ON Operating
mode
AUTO 0V Zone 2,
Zone 3 or
Zone 4
OFF OFF Standby
mode
OFF +12V
or 0V
Any
setting
ON ON Operating
mode
OFF +12V
or 0V
Any
setting
OFF OFF Standby
mode
4 IR IN/IR OUT 1-4
These mini-jacks accept and output remote-controlled codes in
electrical format, using industry-standard protocols, for use with “IR-
repeater” and multi-room systems and related technologies.
All NAD products with IR IN/IR OUT features are fully compatible
with the M17. For non-NAD models, please check with your other
product’s service specialists with respect to their compatibility to
the M17’s IR features.
IR IN
This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another compatible device
to allow control of the M17 from a remote location.
IR OUT 1- 4
Connect IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4) to the IR IN jack of
a compatible device.
Command and control the linked compatible device by directing its
own remote control to M17’s infrared receiver.
IR IN and IR OUT 1/IR OUT 2/IR OUT 3/IR OUT 4
Connect the M17’s IR IN to the IR OUT of a compatible device.
Connect also the M17’s IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4) to
the IR IN of a compatible device.
With this setup, the M17 acts as an “IR-repeater” allowing the device
connected to the M17’ s IR IN control or command of the other
device linked to M17’s IR OUT 1 (or IR OUT 2/IR OUT 3/IR OUT 4).
5 +12V TRIGGER OUT1/OUT2/OUT3
The M17 has three +12V TRIGGER OUT ports (OUT 1, OUT2 and OUT3)
that can be congured to supply +12V DC to a linked component or
system. See discussion on Trigger Setup at the “Setup Menu” literature
for guidelines on how to congure +12V TRIGGER IN/OUT.
Use a 3.5mm mini-jack connector to pass +12 volts at a maximum
current of 50 milliamps to an auxiliary equipment such as a
multichannel amplier or subwoofer. The center conductor (hot) of
the 3.5mm jack is the control signal. The outside conductor (shield)
is the ground return-path.
This output will be 12V when the M17 is ON and 0V when the unit is
either OFF or in standby mode.
+12V TRIGGER IN
With this input triggered by a 12V DC supply, the M17 can be switched
ON remotely from standby mode by compatible devices such as
ampliers, preampliers, receivers, etc. If the 12V DC supply is cut o,
the M17 will return to standby mode.
Connect this +12V TRIGGER INPUT to the remote device’s
corresponding +12V DC output jack using a mono cable with
3.5mm male plug. The controlling device must be equipped with a
+12V trigger output to use this feature.
6 AUDIO 1-7 IN/VIDEO INPUT 1-3
These comprise the M17’s other sets of principal input. Connect
these audio and video input ports to corresponding output ports of
compatible source components such as DVD players, CD players or
cable/satellite boxes.
AUDIO 5 IN, AUDIO 6 IN and AUDIO 7 IN are ideal for the connection
of the analog output of line-level audio sources like a CD player or
Stereo tuner.
The Left Channel of AUDIO 1 IN is the assigned port where the
supplied 3.5mm female jack to RCA plug Adapter can be connected.
Plug in the Audyssey microphone into the adapter for Audyssey
Auto Calibration.
AUDIO 3-4 OUT/VIDEO OUT
Connect AUDIO 3 OUT (and/or AUDIO 4 OUT) to corresponding
recording components or audio/video input ports of compatible
sources like cassette deck, CD/DVD recorder or outboard audio
processors.
The signal present at AUDIO 3 OUT is determined by the current
source selected. There will be no output at AUDIO 3 OUT when
AUDIO 3 is selected. Likewise, there will be no output at AUDIO
4 OUT when AUDIO 4 is the active source input. This prevents
feedback through the recording component thereby preventing
possible damage to your speakers.
When congured, AUDIO 3 OUT and AUDIO 4 OUT are the same
assigned ports for Zone 3 and Zone 4 respectively. See also Zone
output description below.
7 COMPONENT VIDEO INPUT 1-2,
COMPONENT VIDEO MONITOR OUT
Connect the Component Video Input to Component Video output
of compatible source components, typically a DVD player, BD
player, digital cable box or other applicable components. Connect
Component Video Monitor Out to the Component Video input of a
compatible video monitor/TV.
Be sure to observe consistency in connecting the Y/Pb/Pr jacks
to the corresponding sources/inputs. The routing of the two
component video input is fully congurable via the Source Setup
item of the Setup Menu OSD.
The M17’s sets of component video input and output are fully
wideband and compatible with allowable HDTV formats.
IDENTIFICATION OF CONTROLS
REAR PANEL
9
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD M17 AV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD M17 AV in the language / languages: English as an attachment in your email.

The manual is 7,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD M17 AV

NAD M17 AV Quick start guide - English - 2 pages

NAD M17 AV User Manual - German - 38 pages

NAD M17 AV User Manual - Dutch - 38 pages

NAD M17 AV User Manual - French - 38 pages

NAD M17 AV User Manual - Italian - 38 pages

NAD M17 AV User Manual - Swedish - 38 pages

NAD M17 AV User Manual - Spanish - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info