· These INPUT/OUTPUT terminals are dedicated only for ZONE 2
SPEAKERS and corresponding STEREO and BRIDGE mode settings.
· Always turn OFF the CI 940 and other components in the system
before connecting or disconnecting anything to the INPUT/OUTPUT
terminals.
· Connect the output from a pre-amplier or processor, such as a
surround-sound decoder, to the INPUT terminals. Use a twin RCA-
to-RCA lead to connect the left and right “Audio Output” of the
preamplier or processor to these INPUT terminals.
· The OUTPUT terminal is a line level “loop through” output. The
same level of input signal at the INPUT terminals is available at the
OUTPUT terminals thereby allowing the same signal to be shared or
passed on to another amplier.
2 ZONE 1 (INPUT/OUTPUT)
· Same description as item 1 above (ZONE 2 – INPUT/OUTPUT)
except that these terminals are dedicated only for ZONE 1 SPEAKERS
and corresponding STEREO and BRIDGE mode settings.
3 ZONE 2 SPEAKERS
· Connect the speaker cables to the supplied speaker connector with
reference to ZONE 2’s speaker terminal markings in the rear panel.
· In STEREO mode, ensure that ZONE 2 “R+” is connected to the “+”
terminal of your right speaker and the ZONE 2 “R-” is connected to
the speaker’s “-” terminal. Connect the ZONE 2 terminals marked “L+”
and “L-” to the left speaker in the same way.
STEREO MODE
SPEAKER CONNECTION
ZONE 2 “R”
TERMINAL
ZONE 2 “L”
TERMINAL
R+R-L+L-
Left speaker terminals+-
Right speaker terminals+-
· In Bridge Mode, connect the single speaker to the terminals marked
ZONE 2 “R +” and ZONE 2 “L+” ensuring that “L+” is connected to
the speaker’s “+” terminal and “R+” connected to the speaker’s “-”
terminal.
BRIDGE MODE
SPEAKER CONNECTION
ZONE 2 “R”
TERMINAL
ZONE 2 “L”
TERMINAL
R+R-L+L-
Speaker terminals-+
BRIDGE MODE
ZONE 2 can be congured to be MONO (Bridge mode), more than
doubling its output power. This way, ZONE 2 can be used as part of a
high power stereo or home-theatre system by connecting additional
power ampliers. In this mode, the amplier section will react as
though the speaker impedance has been halved.
In Bridged mode, ZONE 2 will produce approximately 70W into an
8ohm loudspeaker. Low impedance speakers (under 8 ohms) are
not recommended when using Bridge mode as these may cause the
amplier’s thermal cut-out to operate if played at high levels.
4 ZONE 2 SELECTOR SWITCH
· This selector switch is dedicated only to Zone 2.
· Depending upon the speaker setup connection, slide selector
switch to either STEREO or BRIDGE as applicable.
· Refer to item 3 above (ZONE 2) for corresponding speaker
connections at STEREO or BRIDGE mode.
5 ZONE 1 SELECTOR SWITCH
· Same description as item 4 above (ZONE 2 SELECTOR SWITCH)
except that this selector switch is dedicated only to ZONE 1.
6 ZONE 1 SPEAKERS
· Same description as item 3 above (ZONE 2 SPEAKERS) except that
this is dedicated only to ZONE 1 speakers.
IDENTIFICATION OF CONTROLS
REAR PANEL
INPUTOUTPUTINPUTOUTPUT
ATTENTION!
Please make sure that the CI 940 is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated
components while making or breaking any signal or AC power connections.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for NAD CI 940 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of NAD CI 940 in the language / languages: English as an attachment in your email.
The manual is 1,05 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
