Manual NAD c425 (page 7 of 68) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

161044

Zoom out

Zoom in

1/68

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

8 Preset/Tune - The PRESET/TUNE button toggles between two

different modes:

a) Preset mode: In this mode you can use the PRESET/TUNE

Control (No. 10) or to select a Preset. When Preset

Mode is selected "PRESET" will scroll once through the display

and the PRESET indicator lights up in the display.

b) Tune mode: By rotating the PRESET/TUNE Control (No. 10)

or you can engage automatic or manual tuning

respectively down or up the frequency band. When Tune mode

is selected, "TUNE" will scroll through the display once.

9 Display Area - The display area gives all vital information on the

status of the tuner.

Displayed are:

• Band and frequency of current station, RDS PS (station name), or

RDS Radio Text. The latter two only if RDS is available; select using

the Display button (No. 7).

• If an FM Stereo broadcast is received.

• If the FM station also broadcasts RDS.

• If "Memory" has been engaged

• Preset number if the current station is stored in the tuner’s

memory bank.

• If Blend and FM Mute/Mode are switched On.

• Radio Signal Strength. The bars just below "ANTENNA" indicate

the radio station’s signal strength. The more bars are lit, the

stronger the station.

NOTE

The infrared sensor, which receives commands from a remote control

is located on the left side of the display window. There must be a

clear line-of-sight path from the remote control to this window; if

that path is obstructed, the remote control may not work.

10 Preset/Tune Control (TNR 1 Figure 3)- The function of this

control depends on the tuning mode selected with the PRESET/TUNE

button (No. 8). The PRESET/TUNE (No. 8) button toggles between the

two operational modes:

a) Preset mode (indicated in the display area): Rotate the

PRESET/TUNE Control to the left to scroll to a lower number

Preset; rotate the PRESET/TUNE Control to the right to scroll to a

higher Preset number. This is a "wrap-around" function, so that

going from the highest number Preset, the tuner will go to the

lowest Preset number or vice-versa either up or down when

tuning.

b) Tune mode: Rotate the PRESET/TUNE Control in either direction

for more than 1 second to engage automatic tuning respectively

up or down the frequency band. The tuner will search

automatically for the first reasonably strong radio station, where

it will stop. Rotate the PRESET/TUNE Control again for 1 second

to start searching again.

By briefly rotating the PRESET/TUNE Control in either direction you

will engage manual tuning respectively up or down the frequency

band for precise tuning to a specific frequency. With each brief

rotation, the tuner will take 0.05 MHz steps on FM so you can

accurately tune into the desired frequency. For AM the tuning steps

are set at 10 kHz (120V version) or 9 kHz (230V version).

This tuning mode can also be useful when trying to receive a radio

station, which is too weak for the auto search mode. When tuned

accurately to a station, "TUNED" will light up in the display. The

muting circuit however may suppress very weak radio station signals.

If such a very weak station is in stereo it will have a high level of

background hiss. Switching to Mono Mode and disengaging the

muting circuit by depressing the FM MUTE/MODE button (No. 5) will

allow the station to be heard and will cancel most or all of this

background noise.

NOTES

Automatic tuning is available on both FM and AM.

The PRESET/TUNE and Controls are used in conjunction

with the Memory (No. 4) and Display (No. 7) buttons to add and

memorise user defined names to Presets. Refer to the separate

chapter "Storing, recalling and labelling Presets" for more

information.

11 Sleep Mode (TNR 1 Figure 3) - The Sleep Mode timer will switch

the C425 to Standby mode automatically after a preset number of

minutes. Pressing the TNR 1's SLEEP button once will display the

setting of the sleep time increment. Pressing the TNR 1's SLEEP

button a second time within a 3-second period will change the sleep

time increment in 30-minute intervals, after which time the C425 will

automatically switch into Standby mode. To adjust the sleep delay,

press the TNR 1's SLEEP button twice; first to display the sleep time

increment, and a second time to change the sleep time increment.

Each consecutive press increases the sleep time in 30-minute

increments from 30 to 90 minutes. To cancel the sleep mode,

continue pressing the TNR 1's SLEEP button until "OFF" displays.

Switching the C425 to standby from either the TNR 1's OFF or the

C425's Power button will also cancel the sleep mode

12 Dimmer (TNR 1 Figure 3) - The brightness of the C425’s VFD

can be adjusted to match your room’s ambient lighting. Press this

button once for 1/2 VFD brightness, a second time for completely

darkening the VFD, and then a third time to bring the VFD back to

full brightness. The brightness will revert to full brightness when

power is cycled.

Introduction

C425 072006.qxd 7/28/2006 11:31 AM Page 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD c425 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD c425 Manual

Product: