493509
8
Zoom out
Zoom in
Previous page
1/24
Next page
10 REMOTE SENSOR: Point the SR 8 remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
C 725BEE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the C 725BEE with the
remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30o in each direction of the front of the remote sensor.
11 RECORD OUT/ZONE 2 SELECTOR: This knob doubles as both a record
and zone source selector. Rotate knob and select the Source you would
like to be directed out to REC OUT/ZONE 2 output port in the rear panel.
The directed Source signal at the REC OUT/ZONE 2 output port could
be used for making audio recordings or as an audio input to a separate
zone in your home.
ABOUT ZONE FEATURE
The Zone feature allows one to simultaneously listen to another active
Source of the C 725BEE that is dierent from the currently selected Source.
For example, while the C 725BEE is at CD mode, you can set the RECORD
OUT/ZONE 2 SELECTOR knob to TUNER” and the active tuned stations
audio will be directed to REC OUT/ZONE 2 output port in the rear panel.
You can then feed the REC OUT/ZONE 2 jack to another amplier or receiver
that is located maybe in another area of your home or building. With your
separate amplier or receiver selecting the fed signal and with speakers
connected, you can then enjoy listening to the tuned station. You can
vary the level of the tuned station by adjusting the Volume control of the
separate amplier or receiver. Refer also to the item USING THE
ZR 5 REMOTE CONTROL at the REMOTE CONTROL section of the
the IDENTIFICATION OF CONTROLS page.
12 VOLUME: The VOLUME control adjusts the overall loudness of the signals
being fed to the loudspeakers or headphones. Turn clockwise to increase
the volume setting; counter clockwise to lower it. The VOLUME control does
not aect recordings made using the REC OUT/ZONE 2 output but will
aect the signal going to the Pre-amp output (PRE OUT).
NOTE
If the Volume level is adjusted using the SR 8’s [VOL ] buttons, the
lower line of the VFD will show “Volume Up” when level is increased or
Volume Down” if level is decreased.
13 PHONES: A 1/4” stereo jack socket is supplied for headphone listening
and will work with conventional headphones of any impedance. The
headphone socket will work in parallel to the selected speakers. To
listen to headphones only, de-select Speakers A and/or B. The volume,
tone and balance controls are operative for headphone listening. Use
a suitable adapter to connect headphones with other types of sockets,
such as 3.5mm “personal stereo” jack plugs.
NOTE
Make certain that the volume control is turned to minimum (fully
counter-clockwise) before connecting or disconnecting headphones.
Listening at high levels can damage your hearing.
14 A SPEAKERS B: The SPEAKERS A and B buttons engage or disengage
the speakers connected respectively to the SPEAKERS A and SPEAKERS
B terminals on the rear panel. Press A to switch ON or OFF the speakers
connected to the SPEAKERS A terminals. Press “B to switch ON or OFF
the speakers connected to the SPEAKERS B terminals.
15 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the
audio output of a Media Player. The LED on the MP input button will
illuminate when an external Media Player is connected to this socket.
16 INPUT SELECTORS: These buttons select the active input to the NAD
C 725BEE and the signal sent to the loudspeakers, headphones and the
PRE OUT socket. The buttons on the remote control handset duplicate
these buttons. The selected input will be displayed in the VFD.
MP (MEDIA PLAYER): Selects a line-level source connected to the MP
sockets as the active input. If the DATA port of the optional NAD IPD 1
Dock with iPod (NAD IPD 1) is connected to the corresponding DATA
PORT in the rear panel, your iPod player docked and with the NAD IPD
1’s AUDIO OUT also connected to the rear panel MP input, the lower
line of the VFD will show “iPod Connected”. Refer also to LISTENING TO
YOUR iPod PLAYER under the OPERATION main heading.
If an external Media Player is connected to the front MP socket (using
a 3.5mm stereo plug) while listening to a MP line-level source, the
external Media Player will be directly selected with the MP line-level
source immediately disconnected. It is recommended to mute the
volume or switch to a dierent input before plugging/unplugging the
external Media Player cable.
CD: Selects the CD (or other line-level source) connected to the CD
sockets as the active input.
TUNER: Toggle to select AM, FM or DAB (230V version only) tuner band.
DISC: Selects a line-level source connected to the DISC sockets as the
active input.
AUX: Selects a line-level source connected to the AUX sockets as the
active input.
TAPE: Selects the Tape (or other line-level source) connected to the
TAPE sockets as the active input.
17 TONE DEFEAT: Tone Controls are enabled or disabled by pressing this
button. The lower line of the VFD will show Tone Defeat when the tone
controls are bypassed or Tone Active” if the tone controls are enabled.
18 TONE CONTROLS: The NAD C 725BEE is tted with BASS and TREBLE
tone controls to adjust the tonal balance of your system. The 12 oclock
position is “at with no boost or cut, and an indent indicates this
position. Rotate the control clockwise to increase the amount of Bass or
Treble. Rotate the control counterclockwise to decrease the amount of
Bass or Treble. The Tone controls do not aect recordings made using
the REC OUT/ZONE 2 output but will aect the signal going to the Pre-
amp output (PRE OUT).
19 BALANCE: The BALANCE control adjusts the relative levels of the left
and right speakers. The 12 o’clock position provides equal level to the
left and right channels. A detent indicates this position. Rotating the
control clockwise moves the balance towards the right. Rotating the
control counterclockwise moves the balance to the left. The BALANCE
control does not aect recordings made using the REC OUT/ZONE
2 output but will aect the signal going to the Pre-amp output (PRE
OUT).
IDENTIFICATION OF CONTROLS
FRONT PANEL
8
ENGLISH FRAAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C 725 BEE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C 725 BEE in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C 725 BEE

NAD C 725 BEE User Manual - German - 24 pages

NAD C 725 BEE User Manual - Dutch - 24 pages

NAD C 725 BEE User Manual - French - 24 pages

NAD C 725 BEE User Manual - Swedish - 24 pages

NAD C 725 BEE User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info