30282
103
Zoom out
Zoom in
Previous page
1/110
Next page
ROYAL
pro
102
This can be avoided using the following procedure:
1. Install the servo output levers for the flap and
aileron servos at right-angles to the pushrods.
2. Determine the centre of the working range of
the control surface:
For example: the working range of the control
surface (e.g. camber-changing flap) is from
+20° ... -60°, starting from the neutral position
(flap in line with airfoil)
The centre of the flap’s working range is
therefore -20°.
Now adjust the flap pushrod so that the flap is
at the -20° point when the servo is at centre.
Tip:
First select the servo in the menu
Servo.Ca-
librate
, then select the percentage value for
the point
P3, and finally press the allocate
button for the 3-D digi-adjuster; the servo now
runs to its exact centre position.
3. Both servos
FLAP+ and AILERON+ should now
be calibrated at points
P1, P3 and P5 (also
points
P2 and P4 if necessary), so that both
pairs of control surfaces are at exactly the same
deflection at all points (in our example at +20° /
-20° / -60°.
4. Now adjust the parameter
offs for the mixer
input
Spoiler in the mixers FLAP+ and
AILERON+ in such a way that the control sur-
faces line up correctly.
The following diagram clearly shows the principle
of this set-up:
Mixers:
Mixer Input Note
Combi Sw.
Mixer: Combi-Switch
Î 12.11.2.
Ail-Diff.
Aileron differential
Î 12.6.
Controls
Mix
Mixer: Controls Mix
Î 16.1.3.
ELEVATR+ Elevator
trv' = Control surface deflection
for down-elevator
trv# = Control surface deflec-
tion for up-elevator
Spoiler
Elevator trim correction for Spoiler
(airbrakes):
pt1 = Elevator compensation for
half-deployed spoilers
pt2 = Elevator compensation for
fully deployed spoilers
Flap
Elevator trim correction for Flap
(Flaperon):
trv' = Elevator com
p
ensation for
(e.g.) thermal setting
trv# = Elevator compensation for
(e.g.) speed setting
Thr -Tr
Elevator trim correction for throttle
(motor):
dead = Dead-zone / from which
point does elevator cor-
rection take effect?
trv = Elevator com
p
ensation for
full-throttle
AILERON+ Aileron
Setting for maximum aileron travel
when the Aileron transmitter con-
trol is operated:
trv = Symmetrical deflections
( equal aileron travels
up and down)
Aileron differential is set and ad-
justed in the mixer Ail.Diff.
Spoiler
When the Spoiler control is
operated, both ailerons move in the
same direction (e.g. up) to act as
landing aid:
offs = Offset value
trv = Aileron deflection at full
Spoiler travel
Flap
When the transmitter control Flap is
moved, both ailerons move up or
down together to alter the camber of
the wing section in order to opti-
mise the wing for thermal and speed
flying:
trv' = Aileron deflection, e.g. up
for speed flying
trv# = Aileron deflection, e.g.
down for thermal flying
Ele -Tr
When the elevator stick is operated,
both ailerons deflect up or down in
order to amplify the elevator effect
for aerobatics (“snap-flap mixer”):
trv' = Aileron deflection when
down-elevator is applied
trv# = Aileron deflection when
up-elevator is applied
This mixer can be switched off and
on at any time using the Snap-Flap
switch
+20°
-60°
-20°
N
eutral position
Offset offs
103


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo9 in the language / languages: Dutch as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo9

Multiplex ROYALevo9 User Manual - English - 58 pages

Multiplex ROYALevo9 User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info