30266
51
Zoom out
Zoom in
Previous page
1/57
Next page
ROYAL evo
Page 106
16.2.3. Assigning servos for helicopters
Model type „Helicopter“
Note
Aileron
Roll signal only No mixing
for mechanical rotor head mixing
Elevator
Pitch-axis signal only No mixing
for mechanical rotor head mixing
Rudder
Yaw signal only No mixing
Throttle
Throttle signal with mixed throttle curve,
throttle limiter, direct throttle, throttle-cut
Spoiler
(for fixed wing models)
RPM
Speed regulator control
L. gear
Landing gear signal No mixing
Tow rel.
Tow release signal No mixing
Brake
Brake signal No mixing
Gyro
Gyro signal, including all mixed signals
from gyro mixer
Mixture
Mixture signal for special carburettors
Collect.
Collective pitch signal No mixing
for mechanical rotor head mixing
Thr.lim.
Throttle limiter signal No mixing
TAIL
Tail rotor signal, including all mixed signals
-> tail rotor (e.g. static tail rotor compensa-
tion / Revo-Mix)
HEAD f/b
HEAD le
HRAD ri
HEAD 4
Signal for swashplate servos **
HEAD f/b, le and ri for swashplates with
3-point linkage (e.g. 3-point 120°)
HEAD f/b, le, ri and 4 for swashplates with
4-point linkage (e.g. 4-point 90°)
(electronic swashplate mixing, CCPM)
** Note
To ensure that the electronic swashplate mixing works
correctly, the servos must be connected to the receiver
in a particular, pre-defined sequence. (è 15.5.)
16.3. Sub-menu „Monitor“
The servo monitor acts as a substitute for a receiving
system with servos connected. It enables you check the
function / response of speed controllers, gyro systems,
speed regulators etc., and helps to locate errors.
Two forms of display are available: graphical, with the
output signals displayed in bar graph form, and numeri-
cal, with the signals displayed in % values. You can
switch between the two types of display using the
UP/DOWN (s / t) buttons, or alternatively using one of
the two 3-D digi-adjustors.
16.4. Sub-menu „Test run“
Automatic servo run, which can be used for test pur-
poses and demonstrations, or as an “electronic” aid
when range-checking.
When you select a transmitter control, the software
generates a steadily changing control signal, running
from one end-point of the control to the other. All the
servos operated by this transmitter control (directly or
via a mixer) start running.
You can stop the test run by either of two methods:
Press the REV/CLR button Control “ appears
select no control („ - - - - - - - “)
The transit time can be set within 0,1 4,0 sec.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo12 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo12

Multiplex ROYALevo12 User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info